Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hello,
I'd like to evaluate the performance of an L2CAP CoC on the nRF52840. I was hoping to find an example project which uses this feature but I couldn't see one.
Is...
Hello,
I'm attempting to test the maximum throughput of the nRF52810 using S112 v6.0.0.
The Soft Device Spec v2.0 for S112 implies in Section 15.7 that there is a mechanism...
Hello I am using the nRF52832 in an application where it will be exposed to high magnetic field strengths (e.g. 30,000 Gauss) during normal use. I wanted to know if there...
Hello,
In my project, there is a need to use a service to transfer body temperature. For this I would like to use the standard body temperature service - Health Thermometr...
Hello DevZone,
I am doing a simple test for SPI communication between nRF52840 DK(SPI master) and Arduino UNO(slave).
The Nordic program is based on SDK 14.2.0 spi example...
Hi Support Team,
I used SDK14.1 with nrf52840 on PCA10056. I have a controller which was based on pc-ble-driver running on the host, and a target which was based on ble_connectivity...
Hello!
I have a problem with MQTT Publisher example on my nrf52840 DK.
here is my steps:
1. I edit nrf52840 mqtt example code with
Edit my MQTT settings with:
...
I wonder nrf52832 booting sequence detail.
I knew the booting sequence is MBR -> softdevice->bootloader->application.(is it right?)
but i am not sure how to work MBR and...
I am developing based on "nRF5_SDK_15.0.0_a53641a" [Ble_app_uart], but I am not using LOG in my development environment. If LOG related items in "sdk_config.h" are invalid...
[Ble_app_uart] of the old version of [nRF5_SDK_14.2.0_17 b948 a] is operating correctly, not due to the low-speed clock.
In the old version, the operation of the crystal setting...
I'm trying to get the TWIM peripheral up and running on a custom board with an NRF52810 running SDK15 and S112.
My board is properly advertising, and publishing our custom...
After nightmares with Eclipse I managed to setup Segger within 5 minutes and flash, using the guide from here .
That guide show a lot of very specific stuff you have to...
I have the following ADC code: bitbucket.org/.../eakpq
I have been trying for the past few days to get this code to just perform a single ADC scan, on five channels, once...
