Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I have run into a problem with the nRF sniffer. I used it in late May and early June to debug a BLE connection between a nRF-DK and a HTC Desire 610 and it worked fine...
Hello,
I am trying to communicate urart with nrf52840 and other devices.
But there was a problem.
You can transfer data from the nrf52840 to another device, but if...
Hello,
I need to connect an event handler (i.e. a function) to two NRF_RADIO events:
-NRF_RADIO->EVENTS_ADDRESS
-NRF_RADIO->EVENTS_READY
I know I should use the NRF_RADIO...
Hello ,
I can read the rssi value after the connection is established.
case BLE_GAP_EVT_CONNECTED:
APPL_LOG("Connected to target\r\n");
err_code = bsp_indication_set...
On this question it is said:
"Error code 0x3201 means BLE_ERROR_GAP_DISCOVERABLE_WITH_WHITELIST: Use of Whitelist not permitted with discoverable advertising ."
Why does...
It is not available in Digikey, Mouser distribution restricted to Sweden, not in Farnell???
Where one can order one or there is some problem or new version coming???
Hello,
i am working with SDK 14 type 4 tag library on NRF52832 hardware. I've based my code on the example "writable ndef msg".
When receiving a record, the NFC handler...
Hi All,
We are working with one of project where we are interfacing our nRF51822 with GPS module via UART . now the query is our GPS module works on 3.3V rx/tx logic but...
I'm building an android application using BleProfile classes in the nrftoolbox.
I want to request characteristic write to a peer(nRF51) in MyApplicationActivity inheriting...
Dear all,
I'm using 52810 and have some problem with the S112 softdevice.
My ble app problem is based on SDK 14.0.0.
I download my app hex and the S112 softdevice...
Since upgrading to nRF Connect on my IOS device the DFU won't reconnect to the BLE in the boot-loader after initiation from the application.
The device will migrate to...
Hi all,
I am developing firmwares for the nRF51422 under Eclipse with the ARM GCC toolchain.
I have a matrix of WS2812 (or neopixel) RGB LEDs that I am controlling using...
I need a cheap 2 or 3 button fob or itag to connect to/control my NRF51 firmware. So far I only could find "AB Shutter 3" as input device with >1 button but it is using Bluetooth...
Hi all ,
I have one question . I have 3 board NRF : 1 peripheral and 2 central board . I want to transmiss
data from peripheral board to central board 1 then from central...
