Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hello Everyone,
I want to start working on nRF51822 development kit for my project. but as mentioned on this site : www.nordicsemi.com/.../nRF51822-Development-Kit
that...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
I am having problems with th Master Control Panel (no response from master emulator). When I search devzone, I see an answer related to this question that says cloed because...
Hi,
I have application where I drive LEDs with shift registers. I need to send 14 bytes via SPI every 200us while I am in BLE connection. Timing should be exact as shift...
Hi,
I have a project where I need to communicate using UART BLE between nRF51822 and a PC (MS Surface Pro 3) with Windows 8.1 and embedded BLE hardware.
I have programmed...
Hi,
I have downloaded nRF51_SDK_7.0.1_1d6e5cb.zip and run nRF51_mdk_6_1_0_installer.msi
Neither zip file nor created Nordic Semiconductor/nrf51/ folders have ewp or icf...
Hi,
I think it's a simple question. I want to connect a micro to communicate with a phone via the nrf8001. I ported everything thanks to the guide that you posted (for...
Can we use the tx_complete.count given with BLE_EVT_TX_COMPLETE as an indication on how many packets were sent out from the last ended connection interval?
thank you
...
I have a custom board utilizing an RF51822aa device. To test connectivity to the board I built blinky_s110_pca10028. Using Keil 5.12 I tried to debug the program simply expecting...
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash Download...
where can I get working sample code of nrf51822 with nrf24l01
including code of nrf51822, and code of nrf24l01, both TX, and RX.
in my application, I need 518 to RX data...
I am working with a university project where need to connect up to 20 wireless sensors together with 1 master, which will be communicating with either a computer or smartphone...
I found a IAR project at dir [nRF51 SDK_v4.4.1.31827\Nordic\nrf51822\Board\nrf6310\ble\ble_app_hrs\iar].
But my IAR ARM IDE(ver 6.60 newest) don't support nRF51822.
Do...
