Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
Understood regarding the 8 kHz limit: to stay within the $125\ \mu\text{s}$ budget on the nRF54L, ESB must run at 4 Mbps, unacknowledged ( noack = true ), in plain mode...
nrf54l05, SDK NCS3.0.0, using MCUboot, with external PY25Q16HB as new firmware staging area. During upgrade, attempting to observe CLK waveform, a test wire was soldered onto...
Hello,
I've applied 5V to the anode of the LED, and the cathode is connected to the LED0 terminal of the nPM1300 via a resistor.
I've set the registers in I2C as follows...
While trying to run the FOTA-TEST upgrades from I came across unexpected behavior when the same script fails twice in a row. I first attempt to trigger a FOTA with the following...
Hello,Nordic engineers:
I am using the nRF52832 chip and the nRF SDK v17.1. My device operates in a dual-role (central/peripheral) configuration, and I am using the Nordic...
Title: SoftDevice Controller: 100% connection establishment failure (HCI 0x3E) with SKY66112-11 PA active
Hi Everyone,
I am working on the following development project...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design and I have two questions about the QM13345 configuration.
1. LUT
The Thingy...
I have been testing the HTTP FOTA procedure as documented here using the 1.5.0 test diffs as provided in .
Many of the messages output by the modem in this upgrade process...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
**Setup**
- Custom board, **nRF54LM20A** , first bring-up. The SoC is powered from an
nPM1300: BUCK1 = 1.8 V feeds VDD.
- External **J-Link** (firmware compiled Jun...
Hello,
I have a tight loop with strict timing requirements that I'd like to run on the FLPR core of the nrf54lm20. In each iteration of the loop, i need to write data to...
Hi，
When we draw PCB, we also need to design it like your DK board? There are several square copper skins under the chip, the middle of which is grounded, and the other...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
