Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello The function scan function is being implemented with nrf52833. The desired action is an action that does not connect immediately when the scan starts, but when you receive...
Using nRF52840 and SDK15.3
I'm seeing some documentation on the DFU process and all that but I'm having to write my own bootloader transport (and lower) layer to implement...
The current PC release of nrfutil.exe, v6.1.2, gives 9 malicious warnings on VirusTotal , including warnings from a couple of the big anti-malware vendors.
I would suggest...
Hi all
I used to use bmi160 for my application with nRF52833 and I am upgrading to bmi270 with nRF52840.
I am struggling to make work the functionalities I used to have...
Hi,
I have an application where I want to send sensor data using advertisement message, and read this message by an iPhone. For test purpose, I am currently transmitting...
Hello,
So, I have a working BLE project on the nRF52840 Dongle and I developed and debugged everything on the DevKit, using Zephyr/nRF Connect for VS Code. From there, I...
Hello, I'm using nrf52832, my own custom board, the UART pins are 10 out, 9 in, no stop bit, no parity and no hardware flow control, baud rate 115200.
Ever so often, in...
Hi,
I'm using SDK17.0.2 example(ble_uart) on nRF52832.When I enabled SPIM to drive sensor,and send data, RTT Viewer logging SOFTDEVICE: INVALID MEMORY ACCESS.
BTW I have...
Hi! This might be non-coherent, I apologize in advance as my knowledge in RF is very limited.
We're developing a sort of 'TX-negotiation protocol' between our peripherals...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
Background - found during testing with proprietry application derived from the 'light_ctrl' sample in nRF Connect SDK, with Time & Schedule Servers added, on an nRF52833DK...
Hi,
i have a question regarding the USART NUS error handler.
In my setup, two Nordic BLE Chips are communicating via the USART service.
One chip is acting as a central...
hello everyone,
i am using nrf52810 with my custom board which contains mpu6050 accelerometer and Gyro-meter so now i want to achieve connectable beacon like it should be...
Hi, I received nRF9160DK kit with a SIM. I want to test SIM registration on Vodafon Network , Data transfer to a server ? Is there any concerned sample available in SDK Connect...
Hell Respected Members.
Referring to my previous question https://devzone.nordicsemi.com/f/nordic-q-a/85221/retaining-rtc-time-after-resetting-nrf52840 . give me a reply...
