Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello, On a custom board, using the NRF52832, we want to know the value of a potentiometer. This value is send via a signal on the AIN5 pin of the NRF52.
So, I tried to...
I am using nrf52833 to make a Thread end device as SED and RCP. All firmware versions use NCS V1.8.0.
The compilation options for OTBR is: CMAKE_OPTIONS += \ -DOT_THREAD_VERSION...
Hi,
I use the BLE_APP_UART example for reference and in the code there is the ble_evt_handler with the following states:
case BLE_GAP_EVT_CONNECTED: case BLE_GAP_EVT_DISCONNECTED...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
Hi,
I'd like to test the Adafruit NFC reader example provided in nRF5_SDK_15.3.0_59ac345. I'm using a nRF52832DK and I2C communication, as shown in the picture:
The...
Dear Nordic Support Team,
I am developing an application for the nrf9160 DK version 1.0.x (nrf connect sdk 1.8.0 and modem firmware 1.3.1). The application depends on other...
I have a project that is reading an external flash chip via qspi. Everything is working well, and I haven't defined the sfdp-bdp field in the overlay file that defines the...
Hi All,
I am trying to test the SPI flash example provided in the zephyr samples folder. Below is my qspi dts configuration.
SDK used: NCS v1.7.1
Same code works in...
Hi Team,
We build the bare application with nRF52840 Soc with the SDK Version 16 with out any RTOS Layer. We are planning to port our code base to Zepher RTOS layer.
We...
Hello everyone!
I am trying to get my Thingy 91 to work, but I am stuck.
When I flash it with pre-compiled .hex at_client sample ( "thingy91_at_client_2021-12-15_cfedfdfa...
Hi, I'm working on nRF9160 modem firmware update.
I have used nRF9160: Full modem firmware update using SMP Server demo and compiled it for nRF9160dk board. While compilation...
We are building an application using McuBoot and Zephyr, providing the provisioning via haptools and packing the image all together. What currently bothers me is that I cannot...
Hello,
I am attempting to use SPI and I just wanted to trial the transceiver option however I am not having any luck. I have tried it three ways but as you’ll see I’ve made...
Hi
few questions on DPPI:
where is it possible to find examples in nRF Connect SDK to learn to use DPPI on nRF91?
Is there corresponding documentation?
For which...
I stopped reconfiguring the broadcast configuration and started the broadcast in the following order: ①, ②, and ③. However, I found that the system may report a hardware error...
