Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Just wanted to share my project of controlling the position of feedback servo motor with Nrf52840 by sending bluetooth commands using nordic toolbox
github.com/.../Feedback...
I used the mpu6050 sensor and did it according to 1.2 of this blog .
The driver of this sensor is in the ncs\zephyr\drivers\sensor\mpu6050 directory.Error after compiling...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
# registration CoAP packet
In option enum, there is no "others". Where can I get this information?
I'm writing an application that transmits data over a mesh network of nRF52840 microcontrollers using OpenThread. I'd like the microcontrollers to prioritize sending MLE traffic...
I want to upgrade my application from v1.4.2 to v.1.5.1. but the Bluetooth init failed. So I tested with the scan_adv, which uses the same logic as my application. This also...
The device communicates okay with JLINK commander v7.00a although at the beginning it always says "Connecting to J-Link via USB...Out of sync , resynchronizing... J-Link communication...
Development Environment: icore7 laptop running Ubuntu 20.04.2 LTS.
Target: To build connectedhomeip sample application for arduino nano 33 ble board and check against laptop...
Hi,
We are building our project with nRF52811 and Segger Studio V5.34. (I have Ubuntu 1804 if it helps.)
We have certain variable configurations but would like the ability...
Hello Team,
My end goal is to send 0 to 600hz signal over Ble using NRF52832[ as explained below image].
So, for this, I have used this GitHub code
https://github...
Hello,
I am working an a product based on the NRF52832 and I need to trigger an interrupt when a capacitive button is pressed / proximity detected (BLE is peripheral and...
Good morning,
I'm starting to develop an application for the nRF52805 using ble_app_hrs_freertos as a base.
The modification I did are:
Ported from nRF52832 to nRF52805...
Hi,
I am developing a beacon scanner on NORDIC Thingy 52 using Nordic thingy52 SDK, Now I want to add NUS(Nordic UART service) in my code to send data to the client(ESP32...
I have successfully built the Dynamic Multi-protocols network with Thread and BLE, and used Raspberry Pi 3B + as Gateway Now I want to integrate more AI into the system, but...
Hi there!
I have a host microcontroller connected to the nrf91. The host microcontroller will enabling the nrf9160 through the enable line. From the documentation, VDD_GPIO...
Hi.
The Zigbee stack used in the SDKs automatically stores the network data in the Flash. I know it is possible to erase the NVRAM data with ERASE_PERSISTENT_CONFIG to...
