Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
As in topic I'am concerned about the impedance of SWD interface drivers.
I'am building and SWD interface multiplexer that will be used with 48 devices using J-Link Pro debugger...
Hi team,
I recently purchased some nRF54LM20A units and I am currently working on interfacing them with a W5500 Ethernet module over SPI. However, I am facing difficulties...
Hello, I am trying to configure the NRF9151-DK, but when opening Quickstart app it cannot verify the board. Here's the log. I've been working with exact same boards, also...
I just programmed 2 Boards.
One Peripheral advertising with 1m Phy and other peripheral with s8 codded phy.
Using NRF connect app and wire sharc I made sure that I really...
I had TWO DKs as described in the title randomly fail on me in the same way, months apart. Additionally, I had an earlier rev DK, 2.1.0 (NRF5340 is NOT the IMCU on this version...
Hi,
I'm working on a project with the nRF52840 using nRF5 SDK v15.3.0 and have been working on enabling dual-bank DFU in the bootloader. During this process I made several...
Dear Nordic
There are two questions. Thanks
Q1. Did you have temperature test report of nRF54LM20A (with NFC functionality)?
Q2. We want to implement FIDO (Fast Identity...
Hi,
I am new to Nordic environment.
I have a project build on nrf5340_cpuapp_ns. I want to enable logs on both non-secure and secure image.
Currently I am only seeing...
Description ===========
I am trying to use the native HTTP/HTTPS AT commands of the nRF93M1 to download a firmware image for an external host MCU.
Hardware and software...
Hello,
I ma gathering some data from nRFCloud API, and I noticed a small issue with the pageNextToken. I noticed this on https://api-docs.nrfcloud.com/#tag/FOTA-Job-Executions...
Hi
In my project I have set CONFIG_BT_AUTO_PHY_UPDATE=n in prj.conf. I am using NRF connect sdk 3.4.0
I have configured both central and peripheral to s8 advertising and...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
Hello Nordic team,
I am working with an nRF54L15dk and have an issue using P0.01 as a GPIO input.
P0.03 works correctly with the same GPIO configuration, but P0.01 does...
This is a follow up to case 356908 which was closed due to no resources available. --- We need to shutdown the modem or we end up locking it in the reset-protection state...
