Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hello,
I am using RFX2411N RF amplifier in my hardware design. I chose nRF52832 as an MCU. In nRF52832 datasheet, it is mentioned that the pins from P0.22 to P0.31 have...
Hi,
We are currently developing a Zigbee network based on nRF52840.
One of our devices was specially designed to contain 8 endpoints. But when an active ep request is...
Hi,
I'm using the BLE_app_interactive example as a starting point for my prototype (with SDK_17.0.2 and SoftDevice s132 ). I am using nRF52DK to read and write data from...
Hi
Im trying connect two peripheral devices through UART
The example project I used is "examples/peripheral/uart"
But i trace the code, it seems that the driver layer...
Hello,
I've been using nrfx UARTE driver on the nrf5 15.2.0 SDK on a nrf52832 and nrf52840 SoC and noticed that during the boot-up the first byte being sent is 0xFF.
Is...
Can I remove resistor R29 (ENCHG) on the ADP536 to disable the charging function and plug my 3.3V supply into the battery connector?
i.e. use the ADP536 for the power management...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
I'm trying to get LPCOMP working in Zephyr.
I'm getting the following error:
error: 'NRFX_LPCOMP_DEFAULT_CONFIG' undeclared (first use in this function)
I can see that...
Hi, Can anyone explain what the "receiver address correlation" from 2.4GHz Radio documentation means in practice? For example, what can I do as a BLE application developer...
For various reasons we need to remove the dfu bootloader to use our custom bootloader. We replace the Nordic bootloader with a temporary one that does the clean-up for us...
Hi,
We're designing a PCB for the nRF52833. We could not find a PCB layout recommendation for the chip.
We did find one for the highly similar nRF52840: github.com/.....
Hi,
We want to buy a nrf5340 module but it came with the Rev C Silicon Revision. Do you have any errata sheet for this revision? I only find Rev A, D and 1 on your web...
Hi - I noticed an issue in the esb library as of nRF5 SDK v17.0.2 and am looking for clarification.
In the function update_radio_bitrate , the minimum retransmission delay...
Hi Nordic Forum,
I am making a media control device using the nRF52840 and nRF5 SDK. I started with the ble_peripheral\ble_app_hids_keyboard but I don't know what is the...
