Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...
Hi, I've installed Visual Studio 1.90.2 + nRF Connect for VS Code Extension Pack v2023.11.3 + v2.6.1 toolchains + v2.7.0-rc2 SDK. Then I create a new application, copy a sample...
Hi,
I have tried the led strip example program and it works. My project will use 88 WS2812B RGB LEDs. For testing I used only 5 WS812B RGB LEDs. If I want to turn on red...
So I was experimenting with the Hardware Codec and I created a simple config which redirects the audio coming from the LINE IN mic to HEADPHONE OUT speakers.
Here's the...
We used the ADC nrf52832 to collect the reference source voltage, 1.240V. It is found that the consistency of each power-on is not good, for example, sometimes it is 2806...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When testing the power consumption of the product with main IC 52832, we found that under the condition of 0dBm 1000ms, the peak current of beacon with PPK2 is about 15mA...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
Hi
I want to migrate my application to Zephyr RTOS platform from old setup given below.
Old Setup: Hardware: nRF52832 board. Soft device: S132 Software: SEGGER Embedded...
Hi, I'm new to Nordic Semiconductor chips.
I have experience programming STM32 and Atmel microprocessors. I would need to program/debug the NORDIC nRF52832 chip, without...
Hello there, I am working on enabling/ disabling DFU in nrf52840dk using ncs 2.4.2. previously i was doing it using ncs 1.8.0 as follows: libraries used:
#include <mgmt...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi,
I use the above function to create a new dataset. When I use SDK 2.3.0, this works perfectly. But when I use SDK 2.6.0 I get the following.
When I tried
arm-zephyr...