Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
nRF54L15, Zephyr +MCUboot. I am unable to redirect LOG_INF() output to RTT.
prj.conf
Can you tell me what is wrong? How to force logger to output to RTT?
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
We are trying to pass interrupts at high speed (clock signal) running at 800khz from port p1 to signal the RISC-V Co-processor to trigger a capture on a 4 bit bus. Is it possible...
Hi,
using nrf connect sdk 3.11, nrf54L15-PDK
I am testing low power with development board, I am trying to reach low power 2.9uA as bench marked.
When GPIO (button)...
I noticed in SD7 SDK16.0.0 when CENTRAL and PERIPHERAL connections are defined, the soft device will return designated central and peripheral connection handles. For example...
Hi,
We are modifying our existing product and adding PA to increase the range. Device right now is developed with nrf5 SDK, but we have plans to move to NCS. However manufacturer...
hi support team,
customer is using our 54L15 for mesh lighting project, here are three questions:
1.
customer needs timer model, i see the "time_cli.c" and "time_svr...
I'm developing for a custom board that has an nRF52832 and an FM25W04 external flash. My application uses nRF Connect SDK v2.9.2. I have a debug build that doesn't use a bootloader...
Gemini gave me some code to help get the phy when a connection is updated which does compile but there is an error warning in vs code. Here is the code:
here is the error...
We are evaluating the nrf54 series chips for a new product. We currently have a product that uses the nrf52 series and the distance measurement library. I see that the nrf54...
Hello,
I'm using nRF52840 with Softdevice S140 7.0.1 and SDK 16 for my BLE application in which I send data via notifications. I'm interested in tracking the hvn_tx_queue...
Hi everybody, I have some problems with flashing my custom PCB with an nRF52832. I saw online that you can flash the nRF52832 using the nRF52840 DK. I have looked into a lot...
Dear Support Team, I have downloaded the latest version of VS Code;
I have also installed the latest version of the nRF Connect for VS Code Extension Pack;
The J-Link...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
We are not using the NRF5340DK board. According to tests, after initiating an SPI data exchange, the program is delayed in executing the next CS pull-high operation, resulting...
