We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
Hi,
I am in the process of migration from SES to Visual Studio; I have imported my project; but it has no active build configuration. When I try and add a build configuration...
I am using 9160 to develop a watch product. During the network test, I found that the description of parameter period tau in CPSMS instruction and xmonitor instruction is...
So, i have created a custom board using the nrf52811 SoC. I tried to upload some bluetooth examples to it, and i can see the device on the nRF connect APP. The problem is...
On firing the following command "$ node cli create-ca-intermediate"
terminal showing error
I am following this link nordicsemiconductor.github.io/.../DeviceCredentials...
Hi support team,
I'm trying to simulate the BDM protocol of the 9s12 chip series. Basically the protocol is as follows: Communication on 1 GPIO pin, output open-drain mode...
Hi,
NCS1.9.1, VSCode, nRF5340DK cannect a NFC tag,
i write text to NFC tag by Adafruit-PN532 with anouher device,
than 5340 mcu how to read the text in NFC tag ?
...
Hi! I would to know how to partition the memory of the board and how to make that secure and trusted. Once I did that there is a way to save some information in that portion...
I'm using a nRF52832 for a product under FAA regulations. The standard requires the BLE module to perform a self-test. What self-test capabilities does the Nordic nRF52 family...
Hi,
I see that the NRFX_SAADC_CONFIG_LP_MODE macro sets the default low_power_mode member for the nrf_saadc_config_t struct used to initialize the adc. What I cannot figure...
Hi Nordic Dev Team,
I've got an application where I want to store two types of log data in my memory flash that I want to send to server eventually via BLE mobile app. ...
Hello, I recently did a ble project, it requires pairing and binding ,
1， I can't find ble central demo
2, The ble central of 52832 will connect to multiple slaves, and...
