i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
I would like to do the wfa certification shown in this page: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/wifi/wfa_qt_app/README.html
What is the...
Hi,
Our product has reached the mass production stage and needs FCC certification. We used the coded phy protocol, s140_nrf52_7.0.1_softdevice.hex. Does this support s2...
Hello Nordic Support Team,
I am trying to implement a ring buffer of structs.
Even though my consumer runs much more frequently than my producer, the buffer becomes full...
Hi Sir, i want to build the 2.4GHz Radio-> transmitter Example Program using PCA10056 but getting the below Error. Attached in Screen Shot.
Building 'transmitter_pca10056...
How to create task in zephyr rtos ???? I know creating task in free rtos.Is there any difference between thread and task ? I heard both r equal but in free rtos it is called...
Good day,
We have a requirement for our medical device to detect disconnection of the Bluetooth link in a very timely and consistent manner.
We have an application layer...
HI
I am using the nrf54l15 SDK version ncs3.0.0 and the Zephyr example. Currently, I am connecting a sensor via SPIM30 and need to read the sensor's data every second, which...
After today's vscode upgrade boards aren't detecting on my pc & on my colleagues pc neither. While same board is getting detected on another one of my colleagues pc. Kindly...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I believe I found a bug regarding PSM (Power Save Mode). Specifically, you can't disable...
Starting with the lbs example from lesson l4e2 of BT fundamentals course, I'd like to send an indication similar to the button (and keep the button). I basically created duplicates...
I am using the nRF9151-DK with the standard (from code examples) firmware . When configuring both P0.13 and P0.17 as ADC inputs, I notice that the current consumption on P0...
I am working with the connected_cs examples on the nRF54L15 DK and trying to swap the GAP roles. In my case:
Initiator = GAP Peripheral
Reflector = GAP Central...
I am working on a Bluetooth Low Energy (BLE) project using the nRF52840 Development Kit (DK) , which has been reconfigured to simulate an nRF52805 chip. The firmware is based...
