Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
I am working on an application with significant constraints on power consumption and distance immunity. After some research, I found the Thingy:53 module, which is well-suited...
We had tried AT#XSLEEP=1 command in nRF SDK 2.5.0 and it worked. We saw it working for both modem FW 2.0.0 and 2.0.1.
When we updated SDK to 2.6.1 and modem FW 2.0.1, the...
I am building and running the Serial LTE application on a nrf9160. But am facing an issue with the application going into a reboot loop when network is activated.
I am using...
Hello,
I am working on building a BLE peripheral using the nRF52 DK board. I want to create both connectable advertisement and unconnectable advertisement (beacon type)...
Custom nRF9160 hardware. UART0 over RX/TX-TTL. Updated to MFW 1.3.6. nRF SDK 2.5.2.
Two issues:
1)
Normal at_client w/ PDN enabled to set APN. LTE Link Monitor, and...
Hi
I have a question regarding the power consumption of my own PCB.
I have taken a power profile of the nRF9160DK dev board and of my own PCB with the same software, but...
Hi,
I was looking for a way time sync among nrf52840 devices and I found "Wireless timer synchronization among nRF5 devices" guide and the git hub.
However, it seems...
Since upgrading to macOS Sonoma 14.4.1 yesterday, I can no longer use my NRF52840 DK (PCA10056). The `JLINK` drive momentarily mounts and then disconnects. This process repeats...
Subject: Assistance Required: Troubleshooting nRF52840 and nRF52832 Connection Issues
Hi,
I am currently working on a project involving a nRF52840 (S140) serving as the...
Hi,
I am on nrfConnect SDK v1.7.0, with a nrf52832, with UART in ASYNC mode.
During the uart event callback, the event type UART_RX_STOPPED, but when I check for the error...
I am having issues getting the LVGL library working with my nRF9160 Feather . I am using SDK version 2.5.0.
I have narrowed it down to the call to: `lv_task_handler()` not...
Hi,
Starting from the AWS IoT sample, I’m having a hard time configuring the connection before calling net_if_up() which abstracts a lot of stuff. I would like to configure...
If you try to write a program on a board with nRF5340 installed, an error will occur.
I can write to other boards using the same J-Link, so I don't think it's a J-Link problem...
