I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
So I have this nRF5340-DK board where the Segger programmer/debugging chip is the same size as the nRF5340 SoC. It recently broke when I was moving and I am about to purchase...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello
I am using nRf52805 based BLE peripheral using the Nordic UART Service (NUS). The device transmits numeric data periodically using GATT notifications (NUS TX), and...
Hi,
We have products in the field using SDK 15.2 with its associated S140 SoftDevice s140_nrf52_6.1.0_softdevice, and bootloader.
We are upgrading our application to SDK...
I've succesfully setup multiple nRF7002DK boards with an example app to connect to WiFi.
One out of the five boards the Wifi does not work. The interface stays down in Zephyr...
Hello community
I have tested the v3.2.1\zephyr\samples\boards\nordic\system_off example and it works fine on my nrf54l15dk. Now i wanted to use parts of it for my custom...
Currently I learn the current DFU example from nrf_sdk but I failed in the last step:
I compiled the bootloader example secure_bootloader\pca10056_uart
in the...
Hello, when sending audio packets using a broadcast stream one can provide the seq_num of the packet (using the function `int bt_bap_stream_send(struct bt_bap_stream *stream...
Symptoms:
When running Bootloader + SoftDevice + App (with SoftDevice enabled in the app), The bootloader runs correctly and starts SD. The app is started, but crashes...
Hi,
I'm using nrf Connect SDK 3.1.0 and want to control three WS2812B LEDs with the LED strip driver. Therefore, I created the devicetree entry similar to the sample:
...
Hi!
We are currently building a product using nRF9161 on (rather old) nrf-sdk version v2.9.2.
After production we are testing the hardware functions of this product using...
We have a product that was built on NRF SDK 1.6.1, which is zephyr 2.6 as far as I can tell. We have ported it to zephyr SDK 3.7 (not NRF SDK) because there have been many...
I struggle with my experimental project of breath and apnea detection. It works except that I cannot reduce the poser consumption bellow 1mA when powered on battery, despite...
Hi I saw NRF Connect for Desktop is in the maintenance state, no more development. New recommendation is NRF Connect for VS Code, right? In this case, how about the PPK2 tools...
