I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi! I know that FindHub is supported on nRF Connect SDK, but I'm wondering if there is any support for it on nRF5 SDK for the nRF52840? The use case would be adding the feature...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
I am beginning to work on a next generation of environmental sensors. The current group of sensors use the i2c, or oneWire communications bus. The current standard micro-controller...
I have two questions: 1. The MCU platform is Apollo4MP, and the battery must be customized with a capacity of 28mAh. The PM model is nPM1300. When using its battery capacity...
Hi
I'm using NRF54L15 DK from Nordic. I have installed VS Code and NRF Connect SDK and toolchain V3.4.1.
I'm following the Fundamentals course, and doing Lesson 1, exercise...
Hi,
I'm evaluating the nrf54l15dk and am trying to make a small application where nrf54 appears as a tag. Upon initialization the `nfc_t2t_setup` returns -1 which does not...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
What this ticket reports
We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
Hello,
I have been a Nordic DevZone member for several years, but I have never published a blog post.
I would now like to contribute a technical article about an open...
Hi,
I've been developing the next version of our product with an nRF54L15 There's external SPI flash attached on QSPI via SQSPI which is working ok (albeit it is very slow...
Hello,
I am trying to understand how the documented tRXCHAIN value relates to the timing of EVENTS_ADDRESS in BLE 1M mode.
In this DevZone ticket:
https://devzone.nordicsemi...
Hi DevZone! I'm migrating an app running on a Thingy91 from SDK 2.5.0 to 3.4.0. I will eventually try to adapt it to the newest Thingy91X. So far I managed to migrate the...
Hi all,
We're building a PoC of a simple BLE device with a following setup:
custom PCB with nrf54l15 rev2 and 32MHz oscillator
FreeRTOS + custom port
nrfx version...
We are observing an unexpected increase in current consumption when enabling the LED driver outputs of the nPM1304.
We configure the LED drivers to Host mode , which by...
