I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I have create a separate .hex file for boot-loader & application. when i try to load them into the nRF52382 through "nRF connect".
It says overwriting has occurred...
In the "ble_app_uart" in the ble_peripheral showing the error?
error is -
Building ‘ble_app_uart_pca10040_s132’ from solution ‘ble_app_uart_pca10040_s132’ in configuration...
I've used the PPK2 for a while now, but as of today it started crashing whenever I re-start a current measurement. Both in Source / Ampere meter mode.
The logging says:...
hello Nordic
i am working with nrf52832, with ncs 1.7.1
i am writing my own driver which will be used by 2 baords
one board have to raise 2 gpios to get power and...
I'm trying to read the CTS characteristic from a BLE server (an iOS device) and part of the requirement from Apple is that the server and client be paired and bonded before...
Hi Friends,
- kit dev NF52840-DK
- IDE : segger studio IDE
- SDK nRF52 16.0.0
I want to port the nfc_writable_ndef_msg NFC example to freeRTOS.
I use the NFC Tools...
I'm learning that there are issues with the early "engineering versions" of the nRF52840, identified with QIAAAA marking.
Apparently the SPI3 BUS is not fully supported...
Hi,
After some strange behaviour of the DAC4716 chip, I want to try and reset it. The datasheet describes a way to do so over i2c using a specific bit stream. How can this...
I am having a N20 Micro Gear Motor with Encoder, I want to read data of c1 and c2 using GPIO pins. Any specificAPI, method or suggestion for this?
I am using nRF5340 along...
We have an application running on an nRF9160 development board (shortly to be ported to a production board), which listens on a serial link for sensor data, which is then...
Hello,
For network testing, I would like to use the Modem Shell App sample with the Thingy:91.
As suggested in the overlay file, I can disable some features, so the Build...
Hello,
I am attempting to use my nRF52810 (testing with the nRF52 DK) to generate square waves using PWM. Ideally, these square waves would operate at 8 or 16Mhz. So far...
Hi,
When will Nordic Connect SDK 2.1.0 be available? When have Nordic qualified SDK 2.1.0 and when is QDID number available (Host and Controller)?
We are running Zephyr...
Hi,
I am using the sensor_server example to develop our application on top of it. The problem I am facing is that, the model publication state (publish address and publish...
