I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
My application uses NVS to store data and it works just fine - no errors reading or writing , and saved data persists between device power cycles.
My application also has...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Dear Support Team，
1. How to use Bluetooth Low Energy CGM service on NCS? Are there any examples for us to refer to? For example, nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral...
I turn on the device, the led turns green. And I use usb to connect it with computer then I open the nrf connect for desktop, the bluetooth low energy tool,
10:51:05.822...
Hi,
Our custom board using the nRF52840 with SDK 15.0.0 experiences a higher current draw if it starts up without the USBD module enabled at some time. The first screenshot...
Hi, I work with SES on an nrf52840 on a custom board. Here is my issue :
My board can be wakeup from SYSTEM OFF with 2 interrupts on 2 differents GPIOs : 1 is connected...
hello Nordic
sorry to nag but i am waiting for an answer on the thread below for more then a week now, hope you can attend to it or at list inform that you are working...
Hello Devzone,
Working on my Ubuntu 20.04 LTS host, I recently lost ability to flash my nRF9160dk board. The embedded J-Link is detected by its serial number, but an attempt...
Hi, we are working on an application with 300 nodes. each node do 10sec advertsiment and afterwards 10sec scanning pls check the picture below
1) Beacon2 for example advertisies...
Hi,
I have added an external reset switch on my custom board. Maybe a stupid question, but do I need a pull-up resistor? Because in de schematics of the nrf52840 dk I didn...
Hi,
i want to send and receive data via uart1 (connect to a raspberry and send/receive text).
Is there a simple example that shows how to accomplish this?
Im using SDK...
I'm trying to implement a really simple script to sample voltage values from 5 different analog pins on my NRF52832 DK (using Segger at the moment). I found the SAADC example...
While nrfconnect-3.11.0-x86_64.appimage works well, the update to 3.11.1 ends up without Apps.
Ubuntu 18.04
NCS 1.9.1
I found a past case and removed the config and...
