I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi All,
We are planning to use MAX 3051(CAN Transceiver) which will be interfaced with the NRF52832 over UART.
Our goal is to decode the incoming CAN messages from the...
I had been using the Andoid 4.24.3 version of the nRF Connect app and had no problem with performing DFUs. With the newer 4.25.1 version of the app I noticed a few things...
While trying to reply further queries, by mistake, above ticket got closed ... So, I need to discuss more to the reted issue in the ticket. When, there is a click on verify...
Hello,
I'm trying to add credential to the modem on the nrf9160. However, i keep getting a -111 error when i'm trying to connect to my server with TLS mode.
When i try...
Hi
I connected the nRF21540 to a nRF52840 like in the application notes.
Here is the schematic:
I implemented the driver and now I try to communicate over the SPI...
Hi
I'm using the PA LNA driver for the nRF21540 with the function:
void mesh_lna_setup_start(uint32_t rampup_start_capture_time, uint32_t timer_index)
Now, when I check...
Hello, the device name is being parsed ok, but the mfg data in scan response seems to be there but not sure how to print it out. Using ncs bt sample direction_finding_connectionless_rx...
Hi there,
I wanted to change the advertising name while running DFU bootloader (secure_bootloader_ble_s132_pca10040), so I basically added what I found here:
https://devzone...
Hey,
my Power Profiler Kit on a nRF52840 DK stops recording after some time with the error message " Corrupt data detected, please check connection to PPK."
The time period...
Hello! I wanted to know if there is a way where I can just send a simple string from the nrf52 to the nrf91 without using any complicated examples, I have been trying to modify...
Hi, All
Just wonder how to view the log info like below, it is used in peripheral uart example.
LOG_DBG ( "tx_done" );
which config/tool allow this please?
Thanks...
I was able to interface a 9 axis MPU9250 sensor with nRF52832 via TWI. Now I want to read more number of sensor's data i.e., I want to read 8 IMU sensors data. Since, nRF52832...
Hello there,
I'm using a nRF52840. I would like to perform a complete flash dump. I have tried using an ST Link V2 and and openOCD. It was only returning errors and the...
Hi,
Im using: nRF Connect 1.9.0, Visual Studio Code. I have: a nRF52480-dongle a nRf5340_DK
I would like to have Samples (code), to have a loop through with the highest...
