I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello!
I am trying to write a program for controlling a servo motor. I got recommended a code for making a PWM signal by someone else from devzone, so I am using a modified...
Hello, I would like to know what is required of me to automatically create com port in windows that would allow me to use my ble device as if it were attached by ordinary...
Hi,
I want to receive some data in my nRF52832 from MATLAB over UART and send some other data from nRF52832 back to MATLAB. I need some bandwidth for data transfer from...
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am try to running this case : cfb
C:\Nordic\NCS...
Hi,
I'm trying to use two nRF52840DK as Zigbee routers. I have the following setup,
Software
Application: Home Assistant
SDK: nRF5 SDK for Thread and Zigbee v4.1...
I really like the flexibility that the CLI from FreeRTOS gives me for making my own commands. Does Nordic have a similar library available that I can just import easily into...
Hi,
since The image management provided by mcumgr is based on the image format defined by MCUboot, so does "nRF Connect android app DFU mode" use mcumgr libraries in it...
I'm developing an Ultra-Wide-Band indoor localization system consisting of beacons (stationary, hard powered) and tags (mobile, battery powered), and am looking for a suitable...
Hi Nordic,
I am developling a porject with nRF5 SDK 17.1.0, with nRF52832.
the 52832 serve as a central role.
1、I am wondering what is the difference between BLE_GAP_EVT_CONNECTED...
Values change rapidly and bt_gatt_notify_uuid is called at 10ms interval while bluetooth connection is set up for 15ms connection interval. I assumed this would simply queue...
I have attached all sleep modes of our controller that i found through forums and from your suggestions.
But my problem is No one of these sleep modes, wake-up through...
Hi,
I am just starting out creating a project to run on an nRF9160 on custom hardware. I have set up a development environment (v1.9.0) through nRF Connect for Desktop...
Hello I use nrf52840 and BME280. I plugged it GND GND SDA 45 (P1.13) SCL 47 (P1.15) VCC 32 (P1.00) I use timer to refresh data and on the first line of the code I init gpio...
Hi,
In the nRF52840 Product Specification 1.7 , page 34 chapter 4.4.1.9 INFO.VARIANT, I read that the hex code of variant "AAF0" is 0x4141 45 30. However the description...
Configuration :
IDE : SES V5.70a
SDK version : NRF5_SDK_17.1.0
Board : NRF52840DK
Hello,
I'd like to use 4 channels of the ADC in a scan mode at a high frequency...
