Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The registered schedule was changed to inactive, but...
Hello everyone,
I am a college engineering student working on a circuits project, and I need some help. The project is to design a proximity device that sounds an alarm...
Hello,
we are using a Flutter App on iOS and Android.
With iOS the data transfer is as fast as expected, but Android seems to have delay of 2 seconds between the data...
I am adding a bootloader to my project for OTA DFU.
App core and net core update was successful in the 1st stage bootloader configuration, I'm configuring a second stage...
Does the NCS stack + nRF7002 support scanning while connected? I would expect it could, to support handoff, but getting errors.
Using nRF7002-DK and NCS 2.8.0.
Compile...
Hi, I have an issue when I try to install the nRF connect SDK. I am using Linux Fedora 39, trying to isntall SDK v2.5.0. Steps taken so far:
Download and install nRF command...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
Hi,
I am having problems getting PSM mode, or at least getting a decent power consumption in PSM mode, because I think the PSM in working properly.
I am using the EVB...
I am using Zephyr to create a program that integrates BLE Mesh and NUS. My goal is to use a sensor_client to read data from a sensor_server, and then send the data, via peripheral_uart...
Need some help with:
nrf5340 - custom board
NO external Flash
DFU over BLE with simultaneous update of both images allowed ( using this devzone concept with static...
I using a BMI323 sensor with address 0x68 on the I2C bus and a custom-made nRF52832 dev kit. when I tried to send some commands to the sensor via I2C, it didn't work.
here...
Hello, I'm writing an application for nRF91 series and I have the functionality mostly working but the "sleep" current is high, about 4-7mA. I assume that this means that...
Hi,
I am currently working with the nRF5340 Audio DKs and have successfully implemented the gateway and handset functionalities.
Now, I want to extend the system by enabling...
With the mcuboot enabled, I'm not being able to disable the boot banners even by doing the below settings in prj.conf file.
CONFIG_NCS_BOOT_BANNER = n
CONFIG_BOOT_BANNER...
Hi!
In our project, we need to send cloud-to-device commands. By "command" I mean a request to do some short action, not a request to change device's configuration/state...
