I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am trying to understand how to implement Serialization mode on nrf52.
Rather than having an observer on the application chip, I want the application chip to get alerted...
Hi , I am using nrf52840 dongle with sniffer firmware which can be found here . I am following that tutorial and when I try to capture zigbee packets in wireshark , it only...
Hi,
It seems like there are many instances of ASSERT/NRFX_ASSERT that execute crucial checks prior to actions like dereferencing pointers, and they perform a reset if the...
Hi,
1-I have successfully developed an app ... \nRF5SDK1702d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_template. 2-I have set a UART example to send...
Hi,
We have some questions from one of our FW guys regarding the configuration of the UART pin:
I looked at the UARTE driver implementation, it configures the UART Rx...
Hi there,
We currently have ~500 nRF52832 devices running nRF5 SDK (bootloader, S132, application). These devices are updated using the nRF5 SDK Secure Bootloader UART DFU...
Hi,
I would like to know if it is possible to configure the optimization level only the application built on top of Zephyr, and not all the project.
I am trying to debug...
Hi-
We have an application that currently does not use the soft device. Eventually we will want softdevice S113 in our application once we start to add some BLE based...
*** BEGINEER ALERT ***
Just thought I'd throw that alert in, so you are aware you can't assume anything in terms of base level knowledge here! I'm coming from a Cypress...
I'm currently playing around with learning how to code in VCS with nRF Connect. I was watching a series of Youtube instructional videos ( https://www.youtube.com/watch?v=MGsZJpdLtco&list...
Hello,
My colleague and I created ESB prx project based on SDK 1.6.0 version and nrf5340 dk.
And some source codes in ncs/nrf/samples/esb/prx/src folder are changed...
Hello,
I am trying to work on a simple GPIO program for the Thingy:91 which involves reading a pin for sensor inputs (this will be 2 sensors eventually). I have tried to...
nRF Connect V 1.6.0
using samples/zigbee/network_coordinator against a nRF52840, I am trying to commission a larger number of devices to join the network. Currently 24 devices...
Firstly, my english is not good,
I am using nRF52840 and my IDE is Keil uvision 5, i want to know, where is the pins SDL and SDA
I am new developer, and please you can...
