Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
I've been developing software that uses pc-ble-driver and a PCA10040 devkit to act as a central. My software is based off the heart rate v5 example written in C, and...
Hi,
We have been working with a Zigbee coordinator based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
We are tring to integrate...
Hello Community,
So I am building a RF system from scratch based on the nRF24l01P transceiver with a PA/LNA, using a balun for impedance matching and a band filter for filtering...
Hi All!
Hope you all are doing well ! . I am new to nrf52833. My requirement is test the range test with CODED PHY @125kbps /S=8 .
For this i tested the example "ble_app_att_mtu_throughput...
Hello.
After performing a secure DFU download, the first attempt to open a secure NUS connection fails with an NRF_ERROR_INVALID_PARAM error. After resetting the device...
I just received the nRFgo Starter Kit and am trying to follow the Starter Guide. The first step is to register the product on the Nordics MyPage (which has been combined to...
Hi, what would be the status of VDD_PA when CSN is high (Power Down mode)? Will it be LOW or Floating/High Impedance?
I know VDD_PA changes to high (1.8 V) or low based...
I've been trying to get Wireshark up and running on Windows. I can't seem to get it working. I've tried managing my Python installations, deleted them, reinstalled them, checked...
Hello,
I am interested in testing the BLE long range mode of nRF52833 (or nRF52820) and have found documentation about the long range testing that has been performed on...
Hello, I am trying to do DFU over BLE for nrf52 devices from another microcontroller (ESP32 to be specific), I couldn't find any data or example code to do this, are there...
Hello,
I have developed an application for my NRF52 DK and I want to port it to an NRF52832-QFAB-R which has a reduced amount of storage. I have changed the parameter "Target...
Hi,
I am following then nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using nRF Connect SDK 1.4.99-dev (installed via the Toolchain Manager)
In part 1.3.2 Build...
I recently switched from 52832 development using IAR to 52833 development using SES. As a result, I downloaded all new versions of the SDK, softdevice and, of course, SES...
There is a marked improvement in the handling of TrustZone in nrfjprog 10.11.0 and 10.12.00, but it seems it's still not quite all the way there. I can do:
and am able...
Hello,
I am developing DFU over a custom IEEE802.15.4 Protocol in our own embedded OS. I managed to write the new Firmware starting at bank1_start address. Now I need to...
