Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
What am I missing when
NRF_SPI_MNGR_DEF(my_spi_mgr, 2560, 0);
causes:
../../../../../../integration/nrfx/legacy/nrf_drv_spi.h:120:37: error: 'NRF_DRV_SPI_INSTANCE_0...
Hey all! I have been using your amazing app timer for a while now but I was wondering if there was a better way to create a low power delay than my current design which goes...
Hello,
My application is the ble_app_uart example of SDK 15.3 extended, and using S112. I'd like to use constant latency mode. Given the app uses S112 for BLE, should I...
Hello,
In demo code of Central_Uart code in nRF Connect SDK, when the scanning is started the scan address (MAC) keeps on changing everytime the code is run. (The central...
Hi, We have a product with nrf24L01p Gazell (LastChangedRevision: 133) that acts as a Host. At the moment I'm trying to pair with this host via a PCA10040 Devkit ( nRF52832...
After nrf52382 is written into the firmware program, the test runs OK. After it is placed for a period of time, it is checked again. It is found that it is not running. Use...
Hi all,
We are running into a problem with our battery powered nRF52.
The nRF is continuously powered by one lithium cell. When the battery is very deeply discharged ...
Hello,
In our current design, our boards use P0.18 connected to an external watchdog to reset the nRF52840. We configure PSETRESET[0]/[1] to be 0x12 (Connected/enabled on...
Hi,
I am using Zephyr to do some action in a main loop and ksleep for 30 seconds. While in ksleep(), I can see that the consumption is 20ua. The board is a very small simple...
I have a Fanstel Evaluation board which can be programmed through 52 DK board, no problem there and i also have built a custom board using the BM833AF modules based nRF52811...
Hi,
I was wanting to know if this function has been changed since mesh SDK v2.2.1? It appears to not behave quite the same. When I call it, I think the mesh does not entirely...
I am currently working on sending some custom data using BLE nrf52.
I find the BPS format best suited for my application but I want to modify the systolic and diastolic...
I am adding dfu capabilities to my app on SDK12.3.
For that, I took the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant...
I am trying to modify the receiver an transmitter examples to change the default bandwidth on both the receiver and transmitter. I have looked through documentation without...
