Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi, I have a question for you! Thank you!
My PCA10040 was not successfully connected to the computer.
The device manager of the computer did not show anything related...
Hi
i am using SDK15.0 .i have tested Secure Ble for firmware update. Its working with my public keys. i want to know is it possible to update firmware without Public key...
Hello,
I am trying to find the IP address of the devices.
Device: nRF52840 DK
Setup: Running virtual Ubuntu 18.04 inside Windows 10 (using VMWare).
I am able to connect...
Is there any recommended way to flash the nRF51822-CEAA-R WLCSP chip?
Should a PCB design have UART design for flashing the nRF51822 chip after it is soldered on? Or should...
Hi, My problem is: When I programing my board using existing hex from SDK, I have no problem. Program working great. But if I building my own hex (build without errors) and...
Hello,
I am using nRF52832. My GPS is connected to GPIO pin (15, RX) and (16, TX) of nRF52832. My TCA9535 is connected to GPIO pin (8, SDA) and (7, SCL) of nRF52832. TCA9535...
Hi all,
I am currently building I2C communication between nrf52832 and a stm32 chip, stm32 as the master and nrf52 as the slave.
The situation is the stm32 couldn't get...
I am not connecting any uart lines to the device. But I feel the assert is being used as the timeout "handler" and then pressing button one resets the device.
I'm using...
Hi,
I'm currently going through this paper on the newest Bluetooth Mesh Standard ( http://www.mdpi.com/1424-8220/18/8/2409) . Although it's interesting to see that this...
Hi, we are using SoC nrf52810 SDKv14.2-SR3v1.2 for our RCU.
1.If there is a scenario the image transfer is finished, and the power lost happens when the old image is being...
Hello,
I am in the process of determining a system architecture for a sensor-bluetooth-android application. The goal is to read sensor information from an Android device...
I'm using Mesh SDK v2.2.0.
I want to create a new custom model,but I don't understand difference between Generic and simple onoff model.
Which model should I study?
I remember reading somewhere an article on how debugging with softdevice was going to be easier, with the debugger doing something along the lines of actually not stopping...
