Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
We are on NCS v2.9.1
We have an existing project on based on the nrf52832, which we use as a hci_spi controller. There, CONFIG_BT_LL_SW_SPLIT is set. We are now porting...
Hi Support Team
We try to integrate the flowing links' sample code of Mesh Sensor, Mesh LPN and Mesh DFU to one project for nRF52832, but we found that the memory usage...
i'm migrating my application from nRF53 (SDK 2.6.0) to nRF54L15 (SDK 3.0.1) and i've started to get crashes in the soft device.
sometimes it reboots without any logs at...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
Hi Support Team
We try to integrate the flowing links' sample code of Mesh Sensor, Mesh LPN and Mesh DFU to one project for nRF52832, but we found that the memory usage...
Hi there.
I am trying to implement a 16-bit, 32kHz, 2 channel i2s interface which is being fed by a FIFO (the final source of this FIFO will be a DAB/FM radio module but...
Hello,
I am developing a mesh solution when the nrf52840 USB dongle will act as an observer.
I am using the mesh sensor observer sample. I am able to build and flash...
Hi Nordic Team,
I would like to confirm whether enabling APPROTECT also implicitly enables Secure APPROTECT, or if these two protection mechanisms need to be configured...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
I recently bought PPK2.
But am unable to connect it to my Linux PC with Power Profiler v4.1.0.
Below is the log -
08:49:26.328 Error: Failed with exit code 1. Failed...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi, I am seeking assistance with a very weird issue encountered while programming an nRF5340 SoC using a custom debugging-PCB using a SEGGER J-Link EDU debugger.
The debugging...
