I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
As title says, I have a clean install of Xubuntu 23.10, latest nrfutil and toolchain-manager package
My shell is zsh, however "nrfutil toolchain-manager launch --shell zsh...
I am looking at the "mesh_shell" example project. I was able to build the sample for nrf5340 dk this way:
- create a new build configuration for "nrf5340dk_nrf5340_cpuapp...
I am working with an IQS572 capacitive touch IC, and when communicating with this IC, the communication window will shut down if it receives a STOP bit.
I am writing a lot...
Dear all,
I am use nrf5340_audio_dk to run the audio_application and I use the BIS mode. I post 2 loggings at the headset device as the broadcast_sink. All things seems...
When I try to build the SDK example WiFi monitoring it showing error, C:/ncs/v2.6.1/nrf/ext/oberon/psa/core/library/check_crypto_config.h:80:2: error: #error "PSA_WANT_ALG_DETERMINISTIC_ECDSA...
As far as I can tell, it is not currently possible to implement the following functionality in a simple way with pynrfjprog across the various device families.
* What is...
Dear Sir/Madam,
I am using Zigbee: Light bulb — nRF Connect SDK 2.6.99 documentation (nordicsemi.com) this sample to do an evaluation, and I would like to change the tx...
I'm trying to do an ADC measurement on AIN6 on an nRF52832. This is how I have things set up:
proj.conf:
Overlay file:
ADC initialisation (this gets called on power...
Hi Support Team
We are testing the sensing of zephyr sample in the below directory with nRF52840, but we can't find which callback function is used to get the sensor data...
Hello,
Im trying to update the custom nrf5340 board over BLE. I have managed it using nRF Connect and Device Manager.
I can upload it using nRF Connect, but I need to...
I am developing a firmware for nRF52810.
Does Zephyr support debounce care for push button switches in ncs v2.6.1?
It seems that CAF supports it, but I don't plan to...
Hello!
We are on the process of implementing our own desktop program to run DFU over BLE, similar to how the nRF Connect application does it. We are using SDK 17.1.0 in...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I am working through BTLE Fundamentals, Lesson 6, Exercise 2, and running the code from blefund_less3_exer2 per the instructions and it all looks good on the app COM log:...