I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Let me start by saying we have not ruled out other possible sources of errors at this point. However, right now all the evidence is pointing to an issue with the nRF52840...
I attended the Introduction to the nRF21540 RF FEM for range extension webinar and bought a few nRF21540-DB kits
The first thing I want to do is compare the range increase...
Hi,
We have our own MQTT broker setup with TLS running on a AWS EC2 cloud service. I am building my code based on the MQTT_SIMPLE example. I have only a CA certificate in...
In my project I use nRF52832 embedded in MuRata module. I have a BLE service with capabilities very similar to NUS service.
I've managed to add support for LESC + SEC_MITM...
I am attempting to upgrade from nRF Connect SDK version 1.7 to version 1.9.1
My application is using the nrf52840 on a custom board.
I'm using Zephyr and created a board...
Hallo,
I am starting to develop an application using nrf5340 SoC. I have got two Audio DK and would like to begin my development using nRF Connect SDK.
However, I was...
I was trying to schedule a work item when a struct k_poll_signal is raised by an interrupt, but was unable to get the work to happen. I could tell that the k_work_poll_submit...
Hi, I'm new to this and I was just wondering, since I'm still learning and successfully coded my first app, I'm asking how can you flash / burn / build & run SMD component...
yes, i meet a problem.i notice that isp have done a AOA demo based on Nordic board.
but i use it to get the angle.i find i can't use it.what is this problem?
I am running a nrf52dk_nrf52832 build with SDK v1.9.1. A week ago I was building my project and everything was working fine. Then, my program stopped being flashed - I could...
Hello!
I'm working with nRF9160 on a custom board and I'm trying to use SUPL to improve time to first fix, I'm following the sample nrf9160/gnss/src/assistance_supl.c. I...
I am testing the Asset_tracker_v2 application on thingy-91. I took the SIM card out so the device goes into the boot loop.
The on_state_init () function has the condition...
i am able to succesfully build and flash the simple "hello world" example using segger embedded studio and programmer app.
finding difficulty in logs checking because, the...
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M.
To recreate: build /zephyr/samples/fs/littleFS and set target...
