Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello, Dear Kenneth.
Thank you very much for your response and the answer.
I will change the hardware solution using a voltage detector, but I am not clear yet on the...
Hi, i have this message after installing nrfutil
I checked version of the python, checked requirements, tried to install from sources. I do not know what to do next
Hi, I am experiencing a strange case here where after an update from SDK15.2 to SDK 16, the noinit section of RAM is not working anymore.
When I encounter an error of some...
In v1.4.0 SDK, AES key can be written into kmu slot, but there is no related function for ECC key and RSA key in crypto/nrf_cc310_mbedcrypto/include/mbedtls/cc3xx_kmu.h file...
I am using an STM32L4 chip that sends an update to the nRF52832 on a ublox module over USART. I assume the nordic chip is in the bootloader during the update.
We get a UART...
Hi, I want to eventually be able to programme a custom built chip with an nRF52833 SoC on board, but first I thought I would try with a nordic Thingy:52. My setup is as follows...
Hi,
I have seen a few tickets with people not getting any CTE data received and program restarting after "Waiting for periodic sync lost..".
Did anyone get it to work...
Hi!
Continue the previous case
I try to run zephyr direction finding rx example direction_finding_connectionless_rx
It seems to me that the external antenna is working...
Hi
I am working as a member of a team owning nrf9160 dk. I want to work remotely with the same hardware they have. but right now I do not have physical access to the hardware...
Hi, I installed VS. The screen shot is shown below. How to open, Build, Compile, RUN and Debug sample applications and custom existing SES projects. May, some one explain...
I am trying to program my nRF51 QFAC, but it tells me to adjust my linker settings.
I am using the SDK 12.3 and the softdevice 130 2.0.1.
However, after I apply the...
MCU : nrf52833
SDK : Ver 17.1.0
SoftDevice : S140
I try to call RTC value to external RTC Module by TWIM in BLE authentication rw request event.
But MCU stop to...
Good afternoon,
I built and flashed the Bluetooth Multiple advertising sets sample in VS Code using the nRF Connect Extension Pack onto my nRF5340-DK and come across an...
I am trying to measure my battery level on my nRF51822 beacon board through the internal ADC.
The chip is just advertising itself every 5 seconds.
The measurement works...
