Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi team ,
I am using 15.3 sdk and NRF52832 hardware. and Tool - SEGGER Embedded Studio for ARM 4.30c
I have developed code with DFU feature and and generated .hex file...
Hi,
I want to disable the UART of MCUBOOT to reduce power consumption. I searched in the DevZone and got the answer as below.
I followed the answer above, and created...
Hi there,
For the nRF5340, I read it support the Zigbee . So I just wanna know does it support the Zigbee frequency band in China, which is 780M?
Thanks,
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I know there is the following documentation. ・ SEGGER Embedded Studio Reference Manual : https://studio.segger...
Dear all
I'm using the SD s140 and nRF52840 along with one of the latest SDKs (17...). Everything works fine, I'm able to start advertising and connect, but from time to...
As the title says,
I combined the TWI function with the ble_app_uart example and the three i2c sensor communication was successful.
However, when I added SPI to develop...
Hello, I'm new to nRF Connect SDK.
I managed to add the blinky example to build. I added a custom board.
There is a prf.conf project file with just CONFIG_GPIO=y I'm now...
I'm trying to get the device ID of the lis3dh accelerometer on a Thingy:52
nrf_drv_twi_tx returns 3 as an error. This means NRF_ERROR_INTERNAL --> "If an error was detected...
Hello, when i try to flash my card, (nrf52840) in visual studio code i have those errors
ERROR: The file specified is not a valid hex file, has data outside valid areas...
I am trying to build an application that can switch into MCUBoot's serial recovery mode and receive a new firmware image over the serial port. I'm using NCS 1.7.1 through...
I'm using the nrf9160dk (ns). I started an application based on the SIMPLE_MQTT sample. At first, every this worked. I added my one MQTT client with a different set of buffers...
Hi,
The LE Secure Connections Multirole Example is automatically requesting a pairing/bonding.
Why is it not first just doing a connection and requesting the numeric comparison...
I cannot locate an app in nrf connect for the desktop. What can have contributed to this? Can it have a relationship to the network?
Thank you for your help.
I'm doing some experiments with the nRF52840 and SEGGER Embedded Studio. I'm quite new to C but managed to get desired results using and changing the examples. I'm now trying...
Unable to configure hCI Uart project in Segger Embedded
I need to configure the HCI_UART project to support DTM testing, but I cannot enable the configuration parameters...
