I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hello everyone,
I am working on device based on an nRF52832 that is close to pre-production phase and runs on Zephyr. I have a question because I would like to retain...
Hell there,
I am trying to develop an Android app using nRF52832 chips. I am just planning in a similar situation where I have multiple Nordic thingy 52 devices. How can...
Hi,
We are close to running out of flash on the nRF9160 (with MCUboot enable) and we still have functionality to implement for our product. There are two possible options...
Hello,
I have been developing code for this chip for a while now. In the beginning, I was using the end device role but after a couple of months, I decided to change it...
I'm getting the following linker errors after switching to the latest version of the SDK (17.1.0). I believe I've included the files that define the offending macros (for...
I've made a basic QSPI setup for an MT25QU512. By default the QSPI driver is using 24-bit addressing. To access all of the memory, I'd like to set up the QSPI driver to use...
Hi,
Currently, we have a device that uses the nrf52832 custom board as a Peripheral notify to send the data collected to Pixal 5 (central),
We have a cellphone app to...
Hello Nordic / Zephyr experts,
I am looking for AT command parser for the UART of nRF52840. Want to send and receive AT commands to a LTE modem using MQTT messages. Need...
Hi,
I am aware that nrfutil does not work for OTA updating the nRF53 and was wondering if there was a similar tool that will allow me to achieve this? I need to update ...
Dear BT Mesh experts,
What's the advantage/disadvantage of using the nRF5 SDK for Mesh compared to the nRF Connect SDK ? Consider a rather simple BT Mesh device that provides...
Hi support Team,
Is there a way to make the nrf52840 to connect with only given MAC address (i.e., a MOBILE) ? The MAC address (i.e., a MOBILE) will be changed dynamically...
Hi Support Team,
What's the UBM pad diameter of nRF5340-CLAA?
BTW, any correlation between it and label 'b' in Mechanical specifications in PS?
Best regards
Sal...
When I try to open the .overlay file in SEGGER it shows me an error : "Can't Read file" with the message "Can't open xxxxxx/xxxxx/xxxx.overlay for reading.
Has anyone else...
Hi,
I am running Homekit over Thread sample(NCS/Homekit tag v1.7.0 using MTD-SED conf) on my custom board and I found that the QSPI Flash (MX25R64, as same as the one use...
I want to test OTA in button mode. I have configured the button in DFU project. Now I upload the files in my device in the following pattern:-
1)Bootloader hex file
2...
