Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello
I want to test the nrf52DK board by connecting it to the battery. However, the reset button does not work when only the battery is connected.
To activate the reset...
Hi,
I have three nRF52 DKs，instance is “ nrf5_SDK_for_Mesh_v4.2.0_serial”。When I send commands from PC (UART) to DKs ，DKs running well，but often no response from DK （UART...
We are going through regulation certification testing. And lab is asking what is power tolerance for BLE 1Mbps for the chip. Where can I find this value?
1.Cant make P0.09(NFC1) and P0.10(NFC2) outputs?
Tried both nRF52832 from PCA10040 and a BT module with nRF52840 and on both cant make any of those pins outputs. Tried with...
Hello
I want to test LE Coded PHY S = 2 (500 Kb / s) using the nRF5430 PDK. The SDK used is nRF Connnect SDK v1.4.0.
There is confirmation there.
1. Does nRF5430, nRF...
Hi there,
I am developing an application that uses UART. I am wondering what's the proper way to connect the nRF52840 to the PC. I researched online and found that I could...
I have a few nRF52833 development kits and want to get started with Keil (MDK-ARM). I could not find example projects in the packs that run on the PCA10100 board. Beside of...
SDK 15.3.0, code is based on examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput.
After getting the project to work with nRF Connect on the desktop...
Hi,
just start with SEGGER Embedded and use a usb acm to setup my target
to have a clean structure I moved code from main.c to dedicated files have the USB and BSP
I...
Hey all, I'm new here. So far things have been going pretty well, I am just having an issue with PPI that I can't quite figure out, but I think I'm close. I currently have...
Hi,
We have been working with a coordinator and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hi, I'm working on DFU mesh no serial example (dfu_no_serial_nrf52833_xxAA_s113_7_0_1 ) and want to know any way to check it maybe by using nRF Toolbox or nRF Connect mobile...
I have the Adafruit PN532 Shield v1.3 mounted to an nRF52840 DK, trying to run the ble_nfc_pairing_reference_c example from SDK 17. With no modification to the example code...
I'm calling nrf_drv_uart_rx_abort() in order to read partially captured input from UART in my event handler.
However, instead of receiving a NRF_DRV_UART_EVT_RX_DONE event...
Hello,
We are currently developing a project based on nRF52810.
We are testing some examples to learn more about this chip.
Now we would need to know which signals and...
