I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I want to get the RSSI for each peripheral that is connected to an nRF52 when it is operating as a multi-link central to multiple peripherals. Helpful hints? Sample code...
Hey. I want to wake my s110 device every 30-40 second to advertise for a few seconds only. Is there an example on this or if someone could guide me in the right direction...
Hi all,
I need to using NRF51822 as a clock: second, min, hour, date.... I know I only use RTC as a timer 1s. When NRF51822 power off then time was lost. So, I must be...
Hello,
I have some problem with a specific phone. I try to connect with the nrf52832 using samsung S3 with android version 5.1, the connection takes 20 - 50 seconds and...
Hi,
I am very new to nrf51822 controller. I Used STM32 cortex controller's.
I want to know basic hardware which are the require to start nrf51822 working and programming...
The example nRF51-DK gerbers have solder mask on the PCB antenna. But for the nRF24L01+ EK gerbers, the PCB antenna has the solder mask removed partially, along the length...
Hi,
I downloaded the nrF5 SDK V12.2 from:
www.nordicsemi.com/.../nRF5-SDK
after unzip, I could see the SDCard library under "\nRF5_SDK_12.2.0_f012efa\components\libraries...
Following III. Example code and Enabling whitelisting ,
I try to connect to the "nRF52 DK" board with a whitelist (Android BLE device address),
but I've never connected...
1、I use SDK9.0 ANCS project, the position is as follows:
SDK9.0\examples\ble_peripheral\ble_app_ancs_c\pca10028\s110\arm4
2、I need a project which is contained with...
hello there,
i am giving external supply to nrf51. my external supply is usb 3.3 v. but when i connect it with nordic and then if i check it on multimeter , it shows me...
Hi all,
Does anyone know how much current is meant to be drawn to discover nearby devices? I guess, in other words, how much current is drawn to put the nRF51822 in discovery...
Hi Sir,
I have a NRF 51822 board & MPU 9250 sensor.
I want to read YAW,PITCH,ROLL,ACC_X,ACC_Y,ACC_Z,GX,GY,GZ,MX,MY,MZ values from MPU Sensor.
Could you please share...
