Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
Can the VDD PIN of 4L15 be used to detect the ADC voltage? VDD is powered by a dry battery (3.2V~1.8V), LED+ is powered by 3.3V, LED- will be connected to the I/O of the 54L15...
Hi,
I would like to add MCU boot hardware downgrade prevention in my project.
So i had the following config in prj.conf
Then, when i flash my board i get this error...
I am trying to configure himax camera and stream to app but unable to get image, rather when I am using nrf app to see data i am getting data something like this:
'40-13...
I saw a few questions related to this but nothing I found quite answered my question. We are experimenting with the nRF9161 DK, and we need to securely identify which device...
Hi there, right now I'm working with an application that allows me to collect data via UART from several sensors (two), and I also I have a SIM module that allows me to communicate...
Hi,
I'm trying to build the " tx_rx_non_blocking " sample (ncs2.70, nRF52840dk) but get the following error message -
C:/devtools/nordic/ncs/v2.7.0/modules/hal/nordic...
The CPU runs the main thread every 3 seconds, and for the remaining time, it enters the idle thread. However, after entering the idle thread, it doesn’t save power.
But...
Hi guys,
we are planing to use the nRF52820 as BLE proxy to UART/SPI. It shall receive data from a host controller via UART/SPI and forward it via BLE to a smart phone....
I recently purchased an nRF52840 DK (v3.0.0) to use with my custom nRF9160 boards for firmware loading, debugging, and loading certificates for nRF Cloud. While I can successfully...
For connecting an external TCXO reference, we need to know the specification for the slew rate and levels (Vhigh/Vlow). In the product specs, the clock accuracy is defined...
Hello. I'm newbie with the NCS environment so tell me if I'm saying nosense. I use the nrf connect extension in vs code ide. (SDK: v2.7.0 toolchain: v2.7.0)
I want to...
