I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Hello Team,
I am using ble_peripheral application to establish ble communication with android. But, for some android devices the application automatically disconnects after...
The spec describes the App and Network keys as 16 byte hex strings and states that they are generated by a Provisioner.
Can you please clarify what algorithm is used to...
Hi everyone, I'm Eitan, 4th year electrical engineer student. I'm starting my specialization courses in communications and computers (embedded).
For my final project I want...
Hello, support team.
Now my colleagues are working on the software part for the hardware alpha version of the device with 2 independent antennas for LTE and GNSS. But the...
Hi,
Now I'm using :nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056\s140\arm5_no_packs.
And I want to add 'Characteristic User Description Descriptor...
Hello,
I'm build my application using v1.9.1 and Visual Code. It seems I have an error saying my application size is greater than the flash size.
I CANNOT jettison any...
I have a big issue about WDT during FDA 510K preparing. I have to proof that WDT of nRF52832 is seperated structurally from main system. since nRF52832 have such a seperated...
To whom it may concern,
I have a project (using Zephyr) where I need to switch UART pins while runtime. Is there a way I can handle this? This is how I initialize pinctrl...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
Hello,
I have a question regarding the advertising and scaning mechanism implemented in Zephyr.
To be more precise, suppose the node's radio is in scan mode, and it's...
We want to create solution/project for family of boards using segger embedded studio. We want to create the solution/project in such a manner that new boards software can...
Hello,
I want to build in a reset function for handling certain error states on the 9160DK running nRF Conenct 1.6.0. In the datasheet it appears that nRESET is p0.32 and...
Hi,
I am looking for a way to count the pulses going out of a GPIO pin. If I configure that pin with the input buffer connected, how can I route that signal to a timer/counter...
