HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hello, I'm building the sample Measure battery voltage on a custom board, and I have an error voltage: setup: -134 at runtime. The overlay file is configure as explained in...
I want to implement OTA (Over-the-Air) updates using Thread on the nRF52840 DK board.
Are there any sample codes or references available for achieving this with Thread?
Hello,
I'm trying to use nRF9160 Development kit and it is not showing up in connected devices view in VS code.
Switch position is correct(nRF91) on the development...
I am using v3.0.2 SDK, nrf52832 DK, and I am learning academy.nordicsemi.com/.../ . I encountered a problem in step 4.2:
Please help me find out how to debug
With the NRF_CLOUD_MULTI_SERVICE sample, we'd like to set the GNSS location tracking sample interval to 2s or even 1s.
But we found that the actual time will be about 25s...
Hello everyone, I need to attach a QSPI memory to an NRF54L15 module. I am led to believe that this should be supported out of the box but cannot understand how to use the...
Hello everyone,
I am working on a project where I need maximum range and TX power, since my Bluetooth device will be implanted the signal is strongly attenuated I need maximum...
Hi,
We are evaluating the NRF9151 for live tracking purposes. While testing with the nRF9151-DK we noticed the we had tracking fallouts using AT#XGPS=1,1,1 both during driving...
Hi everyone,
After the latest update of the nRF Connect SDK plugin for VS Code (2025.4.106), we've seen this pop-up appear. We are using v1.8.0 and now we are not able to...
Assume the nRF21540 used as a front end for nRF52840. When the nRF21540 module is in power down mode can it pass the signal without significant loss? If yes what is insertion...
Hello,
I've searched a good amount of online content, but I cannot publicly find a good enough reference design for the nrf52840-DK, natively compatible with Kicad.
...
Now I can use LIBUARTE to receive data from MCU, but have a trouble: it can't receive a whole packet sometime,and return it with 2 parts.
UARTE : 115200/8/1
receive buffer...
Hi Support Team
I installed the NCS V3.1.0 just now. But there was an issue of west: unknown command "build" for the NCS V3.1.0 when I built a sample. Many thanks.
Hi,
I'd like to raise this issue I am having with the v3.0.1 sdk wherein the final build stages I get the message attached
I am using the Lesson 9 exercise 5 sample...
