Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi,
I'm attempting to upgrade an existing project (which is still in the development stage) from NCS 2.7.0 to 3.0.2; this seems to break native TLS, and I'm not sure why...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get the lowest possible power consumption for my Thread device, so I am experimenting with different configurations.
Currently I'm testing with SSED ( Synchronized...
Hi,
We’re developing a product using the nRF54L15 with OTA updates over a cellular network . Since we’re using a low-data-rate cellular connection , the large image sizes...
Hi all,
We are testing with the nrf9151 (mfw 202) on custom hardware with an external active antenna (molex 206640) and a slightly altered SLM (from SDK 2.7.0). Most important...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
I have a requirement where I'm using a .NET-based test adapter that communicates using the Modbus protocol over a serial (COM) port.
Now, I want to develop a BLE Central...
I want to use gpiote and functions like:
- nrfx_gpiote_input_configure
- nrfx_gpiote_in_event_enable
This is added to the top of my document:
#include <nrfx_gpiote...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi Nordic team,
I’m working with the nRF5340 using the Bluetooth: NUS (Nordic UART Service) example from the Zephyr SDK . Since this example primarily uses the UART peripheral...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
