Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hello. I'm currently developing a software for nRF52832AA device. It needs to communicate with external device via UART. It resieves text message and takes some data from...
Hi there,
My question refers to the nRF SDK: examples\dfu\open_bootloader\main.c
When the example is built, the output HEX file contains a section that writes the Bootloader...
How do I get putty to receive output from the Thingy91? I see output in the LTE Link Monitor with the following prj.conf config:
CONFIG_USE_SEGGER_RTT =y
CONFIG_RTT_CONSOLE...
Hi!
My apologies if this question has been asked and answered previously (searched, but didn't find).
We are still developing with ncs version 1.3.2, but would like to...
Hi,
can someone tell me the correct order of AT commands to connect to LTE, activate PSM?
My findings so far:
AT% XSYSTEMMODE=1,0,1,0 => set LTE-M and GPS mode...
Hello, i'm using NCS 1.4.99 with a nRF5340 and i'm trying to use BLE and radio synchronization in the network core. My code run can run minutes without problem but sometime...
Hi,
I am trying to implement the AWS Discovery Sequence with the nRF9160DK board as the AWS Greengrass connected device. I am using the nRF Connect SDK v1.4.0 and used the...
I am trying to wrap my head around this whole Zephyr thing. "Highly configurable" usually goes hand in hand with "not very friendly to newbies" and I am 200% overwhelmed....
Hello all,
I tried to run the nRF52840 dongle and got some issues. I downloaded nRF Connect, SES and the nRF SDK and installed everything. I then tried the examples of the...
Dear all,
I use the nRF sniffer for BLE and nrf52840 dongle to capture the air log.
The tool can capture the air log and decrypt at the begining.
But after a while...
Hi,
I have a nrf9160 device up running for a month and everything looked good. But suddenly it started rebooting periodically, until there is no connection completely. There...
Hi I'm using nrf52 with softdevice s132,
The problem is when I connect nrf52 with my smartphone, the error code 0x3401 occurss after connecting exactly 147~150 second...
Hi,
I'm communicate with my sensor by using TWI ( i2c) driver. Most of the time, no problem.
But yesterday , i was debugging, and and ble disconnect event happen ( it...
