Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hello
I am trying to operate the ble_peripheral_hrs example found at SDK 5.11 (several years ago) for Segger, but I can't found a project (*.emproj) for it.
Have you know...
Hi,
I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART.
I want to an OTA of zephyr OS on that chip over serial and for...
We have a custom device that we profile with a PowerProfiler (external DUT). Device is battery powered.
We have a strange idle current: cca 5 uA for 2 min, then 900 uA ...
Hello,
I am new to the nrf9160. i am quite confused in between nRF Thingy91(pca20035) and nRF9160DK (pca10090) .
What are the steps i need to follow to get start with...
Hello:
I want to change uart0 tx and rx pin from default 28 and 29 to 10 and 11.
I know the i2c pin change need to change nrf9160_pca10090ns.overlay in app.
So I tried...
For quite a while I've noticed that across multiple custom boards using the nRF52 I've been seeing low-level current spikes from a part that is in SYSTEM_OFF mode. They are...
i got 'LIS2DH12_ADDR' undeclared (first use in this function) error when i build my project but i already define it in pca20020.h file.
this image is i define about...
Hi,
I found the TRACE connector on nRF52833 and 52840 DK has its pin 9 connected to ground.
But in the datasheet of JLink/JTRACE, the TRACE connector has following pinout...
Hi,
Could you tell me where can I find some guide how to add DFU into NRF BLE examples, e.g. ble_app_proximity ? I would like to add DFU like a service into the app, not...
We are having a very difficult time soldering the nRF52840 to the PCB. Our Operations Department is asking what the lead finish of the BGA balls is. Would be great to get...
Hi,
I compiled and downloaded GPS sample, I got the following messages:
Tracking: 0 Using : 0 Unhealthy : 0
Seconds since last fix: 600
Scanning [ _ ]
Over 10 minutes...
Dear All,
I have noticed the following behaviour:
When the modem goes to PSM, it is not possible to retrieve the RSRP, using the CESQ or the XMONITOR AT commands. This...
Hi,
I am using NRF52840 DK in our project . I am using 15.3.0 SDK and soft device s140 in our project .Here the nrf52840 dk board is client and other controller bluetooth...
Hello,
SDK: 15.3.0
Hardware: nRF52840-DK
I am attempting to make a simple dimmer with 2 pins/LEDs. I have used the following post.
https://devzone.nordicsemi.com/f...
