hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I am going through the intermediate DevAcademy tutorials right now because I specifically need to use the 52840 dev kit to interface with a SPI driven ili9340 device...
Hi everyone,
Edit: Consider that I'm on ncs 2.6.1
What are the current methods for provisioning an nRF9160 on the nRF Cloud? I have an ongoing project with the nRF9160...
This sample can be found under samples/nrf_compress/mcuboot_update in the nRF Connect SDK folder structure.I want to know the whole decompression process,I added a lot of...
Hi,
I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
Hello,
I am using the hci_usb sample from Zephyr and running BlueZ 5.53 on Ubuntu 20.04. I am trying to increase the ACL packet size from the default value of 27 bytes and...
Hi,
I am using SDK v2.6.1.
Is there any course available on DevAcademy for WebSockets?
For WebSocket i take reference of v2.6.1/zephyr/samples/net/sockets/websocket_client...
Hello there,
I am using nrf connect sdk using vs code.
Toolchain: v2.7.0 SDK: v2.7.0
I have custom hardware board based on nrf52811 SoC.
I have completed a firmware...
Hi
We have a project previously built on NCS v2.6.0 and now we need to migrate it to v2.8.0
I see from v2.9.0 child/parent build setup is not supported and so we are planning...
I'm using ”ncs\v2.8.0\nrf\samples\nrf_compress\mcuboot_update“ this routine.After connecting the Bluetooth, put in the DFU package (mcuboot_update\build\dfu_application.zip...
Hi,
We are trying to enable oversampling in an application that is based on your DF connectionless RX sample, build with Zephyr version 3.4.99.
Something similar was asked...
Hi,
I've a good experience with nRF5340 pre-certified modules and nRF Connect SDK. I'm evaluating leveraging Nordic Thingy:91 X platform to build a new product. However...
Hi Team,
I have some questions following,
1. We created custom board by using nrf52833. for custom board any bootloader needed?
2. We are able to flash hex file into...
Hi i am currently, doing development on nrf52840. where I have 48 number of GPIO's available. for my application, I have peripherals like Touch screen RGB display, UART based...
Hello.
I have two nRF5340 DK boards that I want to use to replicate the demo on https://github.com/NordicPlayground/nrf-knx-iot .
I am using Ubuntu 22.04.
I cloned the...
