here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello,
I'm evaluating the nRF Connect SDK Bare Metal v2.0.0 for an application that requires separation between Secure and Non-secure code. We are evaluating to use the...
I migrate an app from NCS 3.1.0 to NCS 3.2.3.
Using mcuboot with a Thingy:91 or Thingy:91X fails.
flash_img_init results in a flash_img_context, which uses ID 2, the application_slot0...
Hi, Nordic Support!
nrfutil is a replacement for nrfjprog. I have previously relied on pynrfjprog for automated testing and programming. This test procedure uses RTT shell...
I will like to know whether the NB-IoT feature User Plane CIoT optimisation is supported in nRF9151? And if the feature is supported I will like to know the AT command to...
Hi,
We are considering using the new sEMMC SoftPeripheral on the nRF54LM20A with a 4-bit SD card or soldered SD NAND instead of eMMC.
Has anyone tried this? Does it work...
Hi,
I'm in the process of porting our existing nrf5 project to nrfConnect SDK bare metal and am struggling to port our QSPI display driver. Are there any plans to add support...
I’m designing a PCB using NRF9151-LACA-R7 and an NRF52810-QFAA-QFN48 Our CM needs the exact temperature data for SMT reflow , but we can’t find it clearly in the datasheets...
I just developed a BLE peripheral using an nRF54L05 MCU powered by an nPM2100 PMIC. When I flashed it with a simple blink LED firmware using a JLink via SWD, everything worked...
We develop Class C software for a medical device on the nRF54L15 with the S145 SoftDevice. We are also evaluating the nRF54LM20A. We use only the nRF Connect SDK Bare Metal...
NCS 3.4.0 - Thingy91X
If I configure the sysbuild with sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_SECURE_BOOT_APPCORE=n
it builds, but on "west flash" I...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
Hi,
I want to ask if the Nrf54l05 supports application image compression. I asked Nordic AI and they said it’s not supported, but I want to know the reason why it’s not...
I'm setting up a board I just built in NCS, and I made an overlay file for it. Specifically, I am setting up the UART21 peripheral and assigning pin outputs. I made a mistake...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
