hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
When is the anticipated release date for the commercial ready NTN functionality of the NRF9151? I am specifically looking for all Nordic supported Github projects and documentation...
Hi,
I just received two new nRF54LM20-DK boards and wanted to run a Matter quickstart demo. Unfortunately, it’s already failing during programming. What could be cause of...
I've recently received a custom board I've designed and am programming with the nRF52DK, following the procedure in L3 E1 of the SDK intermediate course. I've flashed the...
Dear Nordic FAE Team,
I am currently developing a low-power Bluetooth product based on nRF54L10 , and I have an urgent requirement to optimize the System OFF mode sleep...
Hi,
We are currently in the hardware design phase and comparing different Wi-Fi antennas to find the best one for our product.
Right now we test using: - Scan sample ...
Hi
We currently have products in field test that disconnects from network and never reconnects. It only occurs to a few devices and not all. Restarting the device works...
Hi,
I am using nRF54L15 with Zephyr RTOS in nRF Connect SDK v3.0.2 .
After performing a FOTA update , the device reboots. I need to retain the state of a GPIO pin across...
Hi all,
I recently updated all Segger JLink software using the Segger download links and updated the probe as prompted by VS Code NRF Extension. Up until about two days...
The 54L15DK has two issues. First, what is the purpose of the 3.9pF capacitor on the reset line? If it's for suppressing glitch signals, isn't the capacitance value too small...
I am using nRF Connect SDK 3.2.1 and Toolchain 3.2.1. The hardware I am using is the nRF52840DK and a custom board with the Raytac MDBT50Q-P1MV2 - which contains the nRF52840...
Hi everyone, I’m updating a Matter attribute:
I’d like to know if there is any callback or event that confirms when the attribute report has actually been sent by the...
Hi,
I'm looking for help with an Android DFU failure involving an old nRF51 Legacy DFU bootloader.
Setup:
- Bootloader: nRF51 Legacy DFU v0.8 (SDK 9.0)
- Firmware...
I am at the breadboard stage of this project using an nRF5240DK and various sensor evaluation boards. Additionally, I have an embedded SDCard connected via SPI. The firmware...
We designed a nRF54L15 custom board with a nRF21540 FEM and nRF7001 Module which are on the same SPI with separate CS pins our device tree is configured for this as follows...
