I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi there,
I can't seem to add header files to my project.
The header files underlined in red are not from the Nordic SDK installed from the Toolchain Manager.
...
Hello,
we are currently developing an MQTT Bridge Application. We plan to use a nrf52840 in combination with the nrf9160 as our Bridge which is going to send its data...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
I have developed my thread application based on nrf_sdk_for_thread_and_zigbee and implemented DFU OTA in my application. It is working fine with no issues.
I am using nrf52840...
Hi,
My nrf52840 is not detecting the USB, i tried by pressing the SW5 after that bootloader led starts blinking but not showing any drive in the PC also
can you please...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I have an applications that was using NCS 1.7.1 in its west manifest. I am going through the process of upgrading to 1.9.1
My application using zero latency IRQs and sets...
When I use two nrf5340 audio DK to test the LE audio demo, the handset side always crashes. Especially when I move the DK that is used as the handset.I think that incomplete...
I am trying to interface the Grove 4 Digit Display(TM1637) with the nRF52840 DK.I have successfully interfaced it with ESP32 and get clear output after researching for the...
The main loop in our nRF9160 (NCS v1.8.0) is a typical main loop with semaphore following https://docs.zephyrproject.org/latest/kernel/services/threads/system_threads.html...
Hi
I attempted to create a 32.768 kHz signal from the nRF52840. When I use the HF external clock: NRF_CLOCK->TASKS_HFCLKSTART = 1 ; the generated clock signal looks great...
Hello,
I am waking nRF52805 up from SYSOFF by an accelerometer, after which I want to wait for a second and then start advertising for a short period.
All is working fine...
Dear Nordic,
Could you please suggest and and expamle or advice how to use in-project libraries properly (not 'externally built' as an know example shows). It's better to...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Is there a limitation for number of INT's If is how do I attach same interrupt on multiple buttons
for(..my buttons){ ...
ret = gpio_pin_interrupt_configure_dt(pb, GPIO_INT_EDGE_TO_ACTIVE...
