We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
Hi,
I'd like to test the Adafruit NFC reader example provided in nRF5_SDK_15.3.0_59ac345. I'm using a nRF52832DK and I2C communication, as shown in the picture:
The...
Dear Nordic Support Team,
I am developing an application for the nrf9160 DK version 1.0.x (nrf connect sdk 1.8.0 and modem firmware 1.3.1). The application depends on other...
I have a project that is reading an external flash chip via qspi. Everything is working well, and I haven't defined the sfdp-bdp field in the overlay file that defines the...
Hi All,
I am trying to test the SPI flash example provided in the zephyr samples folder. Below is my qspi dts configuration.
SDK used: NCS v1.7.1
Same code works in...
Hi Team,
We build the bare application with nRF52840 Soc with the SDK Version 16 with out any RTOS Layer. We are planning to port our code base to Zepher RTOS layer.
We...
Hello everyone!
I am trying to get my Thingy 91 to work, but I am stuck.
When I flash it with pre-compiled .hex at_client sample ( "thingy91_at_client_2021-12-15_cfedfdfa...
Hi, I'm working on nRF9160 modem firmware update.
I have used nRF9160: Full modem firmware update using SMP Server demo and compiled it for nRF9160dk board. While compilation...
We are building an application using McuBoot and Zephyr, providing the provisioning via haptools and packing the image all together. What currently bothers me is that I cannot...
Hello,
I am attempting to use SPI and I just wanted to trial the transceiver option however I am not having any luck. I have tried it three ways but as you’ll see I’ve made...
Hi
few questions on DPPI:
where is it possible to find examples in nRF Connect SDK to learn to use DPPI on nRF91?
Is there corresponding documentation?
For which...
I stopped reconfiguring the broadcast configuration and started the broadcast in the following order: ①, ②, and ③. However, I found that the system may report a hardware error...
Hi Team,
I am trying to test on BL653 Nordic board with inverted polarity but we are getting error.
In given example "nCS\v1.8.0\zephyr\drivers\pwm\pwm_nrfx.c " can see...
