Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
hello, my code was built under ncs v2.6.0 and tool chain 2.6.0 without issue, I upgrade them to v2.9.0, then I get these errors, can not figure out how to fix them.
could...
Hi,
From https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/direct_test_mode/README.html , it writes " After programming the sample to your development...
Hi,
I’m working on enabling the asynchronous API on UART1 in the nRF Cloud Multi-Service sample for the nRF9151. Despite setting the necessary configurations, when I call...
I'm using NCS v2.9.0 and attempting to communicate with an ADXL372 IMU over SPI. Occasionally, the MCU successfully reads from the IMU and begins printing values. However...
NCS 2.7 with mcuboot via sysbuild
custom board with nrf52840, 2 custom applications (manufacturig and end-user)
In my application our DFU will be performed over BLE...
Hi,
I have the following Device Tree in my application:
I get the error -134 during the application startup. Debugging the application shows that the error happens...
Hi, I'm developing ble applications.
But there are problems on calling Ble APIs.
If I call the functions that conatins bt_le_adv_start() in main loop(Maybe main thread...
Hi,
I have a BLE interface with services and characteristics and I want to have different level accesses for my characteristics with for example two levels:
level user...
Hi,
Setup:
nRF NCS 1.9.x and nRF NCS 2.5.0
nRF5340 and nRF52840 both with an external crystal attached to HF clock input.
Problem:
Inaccuracy in timing of UART at...
This is sort of a hardware question, involving the RADIO peripheral in the nrf52(840) line. The question is simple. Is there any limitation on when you can change the TXPOWER...
I have a driver for a Piezo buzzer running on bare metal that I would like to port to the nRF connect SDK. The existing PWM-based driver in Zephyr does not fulfill my requirements...
Dear Nordic Team,
I want to connect my nRF9160DK board to my nRF7002DK board and get a wi-fi location. I've followed samples/cellular/nrf_cloud_multi_service as sample...
I have a question about Serial Modem firmware and the AT#XCMUX and AT#XPPP functions.
Are these commands available in the Serial Modem example in the Quick Start?
If I...
Hello,
I've been working with nRF9160 for a while now and wanted to let you know, I love this little piece of hardware. The possibilities, the small form factor, the power...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our hadware is very simple, just a power IC, a nrf52840 and a G-sensor.
Our pre-production...
