We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello
We are using the NINA-B1 on one of our products.
The phone application is working 100% and was very easy to setup.
Till we came to connect our frontend to...
Hi:
we set p21 as Hardware Reset Pin by config UICR.PSELRESET[0] = UICR. PSELRESET[0] = 21
when we use these code to check halt state, but always get DBG_HCSR zero value...
Hello,
I am attempting to install the nRF Connect SDK v1.5 on a Mac Mini with Mac OS 11 with Apple M1 Silicon per the instructions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
We are using the Nordic fork of Zephyr on nRF5340.
Looking at the serial interface peripherals (SPI/I2C/UART), we understand that these have shared resources and only one...
When uploading programs to the nRF24 chip, is there a "single memory space" or is there a "bootloader-only memory space" and a seperate program memory space? or is it all...
Hi All
I am using S130, nRF51822, SDK12, My RTC1 compare events is connected by PPI to ADC, I have set it to generate an adc_ppi_event_handler after 6 consecutive compare...
Hello Team,
First Thanks to all Nordic support:)
My problem :
I have interfaced SGTL5000 with Nrf52832 (used SDK 16) I'm getting the audio data on aux connector and...
Hello!
I have problems with bt_shell sample from sdk-zephyr , when I use SoftDevice bluetooth stack( nrfxlib ).
When I switch on CONFIG_BT_EXT_ADV option in menuconfig...
I got an example that uses PO.13 for analogue input. It does this by referencing it as ADC_0. That seemed to work OK when I hooked up to PO.13 on the nrf9160-DK
Then I changed...
Hi, We are currently attempting to turn off unused parts of our RAM, and the app's linker space is configured to NOT use the turned on RAM. The problem is that the bootloader...
Good afternoon! I would like examples of projects on Soft device S140 long range to test the work of BLE Long Range HCI-USB host - need to be able to connect to them. (scannable...
I'm trying to achieve as close as possible to 48KHz (or 24KHz) LRCLK rate, in 24-bit mode (MCK/LRCLK = 48), on an nRF52832. With the values defined in `nrf_i2s_mck_t ` the...
I want to use libuarte. Target is nRF52832 and SDK17.0.0.2. Do I need to take workaround against Errata109 when using libuarte?
And, I done backport libuarte to SDK15.3...
I have been using nRF Connect SDK v1.2.0 to program my nordic thingy 91, however recently whenever i open IDE, Segger Embedded Studio gives the following error,
"Unrecoverable...
