void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello,
The following error occurred when I ran the program. 00> <info> peer_manager_handler: Connection security failed: role: Central, conn_handle: 0x0, procedure: Encryption...
Now using 52840(S140_nrf52_7.2.0 protocol stack, SDK:17.1.0) Bluetooth packet sending found that the packet sending data length is far less than the actual length to be sent...
I am using a module named MS12SF1 which is a nrf7002+nrf5340 combine module. For wifi initialization, qspi is used. As it wasn't working I added spi4 in the nrf5340dk_nrf5340_cpuapp...
Hi Support Team
If we use nRF52840 develop BLE peripheral base on NCS. What is the maximum number of phones can connect nRF52840 at the same time? Many thanks.
Hello, I'm working on the nrf7002dk WiFi station sample. Most of the time, data is sent and received successfully through HTTP using the HTTP PUT function. However, occasionally...
Hi everyone.
For FCC testing we are required to create firmware builds to transmit at the beginning, middle, and end of the BLE spectrum to allow the lab to verify duty...
This happened last month also during debugging of . I could not use my device for the whole month because the quota was gone in minutes.
Now, new month, new quota, I turn...
Hello,
I am trying to run the asset tracker v2.
I have completed the setup steps and configuration.
Can you please let me know what to do ?
I have read that the -128...
I am inquiring about the ability to run two different radio protocols from a single nRF52840, based on this little marketing aritcle by NordicSemiconductor . Specifically...
Hi,
I am using nrf52840DK and trying to implement a weather station application using thingy53 application example. I am using a Bosch BME280 sensor and could read the data...
Hi, we are using nRF52832 for our project. SDK version is nRF5_SDK_17.1.0_ddde560. SoftDevice is S132.
The project requires TWI to read data from a sensor and send that...
Dear All:
I found that there is a shell interface for the nrf5340_audio project.
I wanted to test the sd card playback from the shell interface.
For the broadcast sink...
I have two nrf9160DKs that are talking to each other over BLE. Things are working fine but I want to eliminate some of the external noise in my environment. Is it possible...
Hi,
I'm using nRF Connect v2.6.2 with Wireshark (3.6) and it is setup with the nRF sniffer + Nordic network keys configured.
I can decrypt packets from another Zigbee...
Basically I want the nrf5340 to reconnect to a paired peer upon reboot. The code seems to suggest that this should happen via directed advertising.
I am testing this with...
