VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi,
Error happens after follow steps:
1. program app.hex+bootloader.hex+device_page.hex+softdevice.hex to boad.
2. use nRF Mesh APP to provision, it runs well
3. add...
I have 2 DK boards neither of which is working.
The first is a PCA10040 V1.2.1. When I plug it into my Window 10 computer with a data cable, Windows says it's an unrecognized...
Hello,
we're developing a NB-IoT application using the nrf9160 and the nrf modem library.
Let’s suppose the modem is in PSM and due to reception/network issues it cannot...
Dear Nordic Team,
on my board with NRF85240 High Voltage mode is used. Accordingly to datasheet (5.3.8.2 Regulator Specifications, REG0 stage), in this mode the following...
Can you help with why I get this serial debug message when trying to start Headset nrf5340_Audio DK in DFU mode
HR [00:00:02.068,450] <err> dfu: SMP_SVR Advertising failed...
Hi!
I have an issue with control of the MAGPIO during RFTEST procedures.
The device is using RF Switch (like Thingy91) and I want to perform SNR/Received signal power...
Hello All,
Hoping to hear your opinion as I have little experience on how reliably the following would work.
The device should count pulses or edges from a reed switch...
Hi,
I'm using a Thingy:53 for some prototyping work. The device is configured with the standard USB CDC ACM as logging backend and I use pyserial-miniterm to access the...
Hello All,
I hope all is well. I have now been using Nordic ICs for close to 10 years and have become familiar with SDK5 and developed multiple applications using it....
Hello,
I would like to fast adc some analog signal from my opamp PCB. I am using nrf5340DK SDK1.9.1 with VS Code.
Got the example code nrfx_saadc.zip from and my first...
Hi,
I'm using the following function in my project, in order to get an idea of how much memory can be reserved with malloc :
This function should return the last value...
Hello,
I have a question about the Kconfig extension for VSCode.
When I use the nrf52840 DK, the Board Selection correctly check the nrf52840dk_nrf52840 and all the configs...
I've been continuing to work on why my power level seemed low after getting the Skyworks FEM in my Fanstel BT840x module going, per this thread:
So far, I've been setting...
I want to increase the rate of data from UARTE to RF FIFO.Can data be transferred from the cache to the RF FIFO using DMA?
nrf52832 nRF5_SDK_17.1.0_ddde560 S132
