Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hi, I want to add CLI in our current firmware. i found a way to do is Zephyr shell. our firmware is based on aws iot sample and nrfconnet sdk1.9.0 after integrating zephyr...
According to data sheet of nRF52832, internal pull up resistance is 13kohm. Can we find the 13kohm internal pull up resistance in the code and can we change that internal...
Ideally we should not get any data when internal pull up resistors of nRF52832 board are disabled and external pull up resistors of SHT 40 Slave sensor are disabled. But I...
Hi,
I haven't been able to actually find out if the VBUS can be used to drive the DETECT signal to go from system off to on mode.
Are there any examples on how to configure...
Hello All, We have designed a custom board for our product and everything pretty much works fine. But now that we have decided to stick to WebBLE, we are facing some issues...
Hi,
I would like to declare my pin in output open-drain, so i use this configuration
My issue is when i declare my pin, I have an unexpected low state that occur...
Hi, I am currently getting started with the Thingy: 91 and am having trouble getting the SDK setup.
I download the file from: https://www.nordicsemi.com/-/media/Software...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi,
I want to monitor the connection state of my device as I have observed situations in which the callback functions defined with bt_conn_cb_register is not fired, causing...
Hi
I have build a sample project nRF5430_audio for nRF5340 Auido DK(two DK, one for gateway, one for headset), following the guide: nRF5340 Audio — nRF Connect SDK 2.0.99...
Hi,
I´m working on a project to send measurement data over ble and receive it. This worked for me, but I want to send the message in my own struct.
What I found in the...
I am trying to use blesniffer on wireshark. I have 2 nRF52840 dongles.
I have successfully captured traces using the 802.15.4 firmware on Wireshark with the dongle appearing...
Hello, I want to know if a typical 50ma Maximum DC-DC converter ic is up to the job of powering up the nrf52840 device working under the heaviest load?
I can't seem to...
Hi Devzone
currently i am doing some test on example central_and_peripheral_hr.
in the orignal example central_and_peripheral_hr is using the BT_SCAN_TYPE_SCAN_PASSIVE...
