I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Again I am asking a question I should not because I cannot find it documented.
I get a pairing request from the central. I need to respond with sd_ble_gap_sec_params_reply...
Hello.
Now, I'm trying to make a Beacon with updatable Major Value, based on sample 'ble_app_beacon'.
I'm not really familiar with BLE and Nordic device, though...
I...
Hi,
We have created GATT servers and tried to connect with one MOBILE APP.
But, we failed.
Although, we could able to connect with standalone BLE, but once we tried...
Hi,
I have been trying to experiment with the nrf5 SDK for thread and zigbee. Our product uses a NRF52840 in the form of a BL654 module and we have been using xbee S2C modules...
Hello, I was reading through the documentation for the nRF Connect for Desktop and I came across a reference to set up the nRF Connect for VS Code. However, I couldn't find...
Hi,
I am using nRF52820on a customer board to run MESH Light project, but I can not start the mesh stack, problem is:
it looks like due to flash limited, but according...
Hi All,
I am new to Zephyr/NCS, so I am a little confused about which UART driver (Zephyr's uart/nrf_libuarte/nrfx_uart/nrfx_uarte) to use to approach this feature with...
I'm evaluating the nRF52840_DK with nRF5_SDK_17.0.2
After doing some tests with ppi to timestamp gpio events, I'm now enabling the softdevice.
This leads to two questions;...
I have been successfully using mergehex with s140_nrf52_6.1.0_softdevice.hex and a bootloader to create firmware packages for my nRF52840-based device and wanted to try softdevice...
When I run the QSPI example in SDK, it can work well both on the PCA10056 and my custom development board. However, when I transfer the example to app_buttonless_dfu, the...
Hi,
I am trying to send the max 240 bytes in NUS SERVICE nRF_CONNECT_SDK
I have seen the ble throughput example and changed
CONFIG_BT_RX_BUF_LEN=255
CONFIG_BT_CTLR_TX_BUFFER_SIZE...
Hi Nordic
We are evaluating nRF 9160 for our next revision of the PCB, and we are testing nRF9160DK.
It came with a sim, which i tried to activate by nRF cloud, but it...
Hello
Is there any example or tutorial on how to use the mpu6050 library?
I just started to program the nrf51822 and hope to find some helpful clues to get me going. ...
I have nrf52840/32 dk and lis3dh accelerometer. I have interfaced two of then via I2C. I want to advertise data of lis3dh xyz acceleration values in the ibeacon advertsing...
Hello，
I am testing nrf52840 low power module on usb power supply, but it's current is about 22ua not 7ua.
hardware design
software design
Can you give me some...
